(Ikke-trådløst) netkort findes ikke af Ubuntu

[Lhademmor]

Hej alle
Jeg har fået overtalt min mor til at prøve Ubuntu som dual-boot med XP, så det skuffede mig naturligvis en del da jeg efter at have installeret Ubuntu opdagede at den ikke kunne komme på internettet - den finder ganske enkelt ikke netværksforbindelsen.
Der er ingen problemer i XP, så det er ikke forbindelsen der er noget galt med.

Her er output af dmesg i terminalen:

Kode: Vælg alt

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.27-3-generic (buildd@vernadsky) (gcc version 4.3.2 (Ubuntu 4.3.2-1ubuntu6) ) #1 SMP Wed Sep 10 16:02:00 UTC 2008 (Ubuntu 2.6.27-3.4-generic)
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009b000 (usable)
[    0.000000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 00000000bfe53c00 (usable)
[    0.000000]  BIOS-e820: 00000000bfe53c00 - 00000000bfe55c00 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000bfe55c00 - 00000000bfe57c00 (ACPI data)
[    0.000000]  BIOS-e820: 00000000bfe57c00 - 00000000c0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fed00400 (reserved)
[    0.000000]  BIOS-e820: 00000000fed20000 - 00000000feda0000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
[    0.000000]  BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
[    0.000000]  BIOS-e820: 0000000100000000 - 000000013c000000 (usable)
[    0.000000] last_pfn = 0xbfe53 max_arch_pfn = 0x100000
[    0.000000] kernel direct mapping tables up to 38000000 @ 7000-c000
[    0.000000] RAMDISK: 7f7ee000 - 7ffef224
[    0.000000] Allocated new RAMDISK: 005e3000 - 00de4224
[    0.000000] Move RAMDISK from 000000007f7ee000 - 000000007ffef223 to 005e3000 - 00de4223
[    0.000000] DMI 2.3 present.
[    0.000000] ACPI: RSDP 000FEBF0, 0024 (r2 DELL  )
[    0.000000] ACPI: XSDT 000FD08A, 005C (r1 DELL    B8K           14 ASL        61)
[    0.000000] ACPI: FACP 000FD1A2, 00F4 (r3 DELL    B8K           14 ASL        61)
[    0.000000] ACPI: DSDT FFFCEA8C, 32D3 (r1   DELL    dt_ex     1000 INTL 20050624)
[    0.000000] ACPI: FACS BFE53C00, 0040
[    0.000000] ACPI: SSDT FFFD203D, 009C (r1   DELL    st_ex     1000 INTL 20050624)
[    0.000000] ACPI: APIC 000FD296, 0092 (r1 DELL    B8K           14 ASL        61)
[    0.000000] ACPI: BOOT 000FD328, 0028 (r1 DELL    B8K           14 ASL        61)
[    0.000000] ACPI: MCFG 000FD350, 003E (r1 DELL    B8K           14 ASL        61)
[    0.000000] ACPI: HPET 000FD38E, 0038 (r1 DELL    B8K           14 ASL        61)
[    0.000000] ACPI: SLIC 000FD3C6, 0176 (r1 DELL    B8K           14 ASL        61)
[    0.000000] 2174MB HIGHMEM available.
[    0.000000] 896MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 38000000
[    0.000000]   low ram: 00000000 - 38000000
[    0.000000]   bootmap 00008000 - 0000f000
[    0.000000] (9 early reservations) ==> bootmem [0000000000 - 0038000000]
[    0.000000]   #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
[    0.000000]   #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
[    0.000000]   #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
[    0.000000]   #3 [0000100000 - 00005dfba0]    TEXT DATA BSS ==> [0000100000 - 00005dfba0]
[    0.000000]   #4 [00005e0000 - 00005e3000]    INIT_PG_TABLE ==> [00005e0000 - 00005e3000]
[    0.000000]   #5 [000009b000 - 0000100000]    BIOS reserved ==> [000009b000 - 0000100000]
[    0.000000]   #6 [0000007000 - 0000008000]          PGTABLE ==> [0000007000 - 0000008000]
[    0.000000]   #7 [00005e3000 - 0000de4224]      NEW RAMDISK ==> [00005e3000 - 0000de4224]
[    0.000000]   #8 [0000008000 - 000000f000]          BOOTMAP ==> [0000008000 - 000000f000]
[    0.000000] found SMP MP-table at [c00fe710] 000fe710
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000000 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x00038000
[    0.000000]   HighMem  0x00038000 -> 0x000bfe53
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[2] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x0000009b
[    0.000000]     0: 0x00000100 -> 0x000bfe53
[    0.000000] On node 0 totalpages: 785902
[    0.000000] free_area_init_node: node 0, pgdat c04a4f00, node_mem_map c1000000
[    0.000000]   DMA zone: 3959 pages, LIFO batch:0
[    0.000000]   Normal zone: 223300 pages, LIFO batch:31
[    0.000000]   HighMem zone: 551734 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x808
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x05] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x01] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x02] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x03] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high level lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] SMP: Allowing 8 CPUs, 6 hotplug CPUs
[    0.000000] mapped APIC to ffffb000 (fee00000)
[    0.000000] mapped IOAPIC to ffffa000 (fec00000)
[    0.000000] PM: Registered nosave memory: 000000000009b000 - 00000000000f0000
[    0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at c2000000 (gap: c0000000:20000000)
[    0.000000] PERCPU: Allocating 41628 bytes of per cpu data
[    0.000000] NR_CPUS: 64, nr_cpu_ids: 8, nr_node_ids 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 778993
[    0.000000] Kernel command line: root=UUID=6A64B59164B5608D loop=/ubuntu/disks/root.disk ro quiet splash
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[    0.000000] TSC: PIT calibration confirmed by PMTIMER.
[    0.000000] TSC: using PMTIMER calibration value
[    0.000000] Detected 2127.991 MHz processor.
[    0.004000] Console: colour VGA+ 80x25
[    0.004000] console [tty0] enabled
[    0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.004000] Memory: 3100604k/3144012k available (2661k kernel code, 42088k reserved, 1180k data, 428k init, 2226508k highmem)
[    0.004000] virtual kernel memory layout:
[    0.004000]     fixmap  : 0xffc77000 - 0xfffff000   (3616 kB)
[    0.004000]     pkmap   : 0xff400000 - 0xff800000   (4096 kB)
[    0.004000]     vmalloc : 0xf8800000 - 0xff3fe000   ( 107 MB)
[    0.004000]     lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
[    0.004000]       .init : 0xc04c8000 - 0xc0533000   ( 428 kB)
[    0.004000]       .data : 0xc03995af - 0xc04c0640   (1180 kB)
[    0.004000]       .text : 0xc0100000 - 0xc03995af   (2661 kB)
[    0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[    0.004000] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.004000] hpet clockevent registered
[    0.004000] Calibrating delay loop (skipped), value calculated using timer frequency.. 4255.98 BogoMIPS (lpj=8511964)
[    0.004000] Security Framework initialized
[    0.004000] SELinux:  Disabled at boot.
[    0.004000] AppArmor: AppArmor initialized <NULL>
[    0.004000] Mount-cache hash table entries: 512
[    0.004000] Initializing cgroup subsys ns
[    0.004000] Initializing cgroup subsys cpuacct
[    0.004000] Initializing cgroup subsys memory
[    0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K
[    0.004000] CPU: L2 cache: 2048K
[    0.004000] CPU: Physical Processor ID: 0
[    0.004000] CPU: Processor Core ID: 0
[    0.004000] using mwait in idle threads.
[    0.004000] Checking 'hlt' instruction... OK.
[    0.017907] ACPI: Core revision 20080609
[    0.072199] ACPI: Checking initramfs for custom DSDT
[    0.491464] ENABLING IO-APIC IRQs
[    0.491635] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.531328] CPU0: Intel(R) Core(TM)2 CPU          6400  @ 2.13GHz stepping 06
[    0.532031] Booting processor 1/1 ip 6000
[    0.004000] Initializing CPU#1
[    0.004000] Calibrating delay using timer specific routine.. 4256.01 BogoMIPS (lpj=8512027)
[    0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K
[    0.004000] CPU: L2 cache: 2048K
[    0.004000] CPU: Physical Processor ID: 0
[    0.004000] CPU: Processor Core ID: 1
[    0.616435] CPU1: Intel(R) Core(TM)2 CPU          6400  @ 2.13GHz stepping 06
[    0.616450] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[    0.620050] Brought up 2 CPUs
[    0.620053] Total of 2 processors activated (8511.99 BogoMIPS).
[    0.620074] CPU0 attaching sched-domain:
[    0.620077]  domain 0: span 0-1 level MC
[    0.620080]   groups: 0 1
[    0.620086] CPU1 attaching sched-domain:
[    0.620088]  domain 0: span 0-1 level MC
[    0.620091]   groups: 1 0
[    0.620187] net_namespace: 840 bytes
[    0.620187] Booting paravirtualized kernel on bare hardware
[    0.620293] Time: 19:03:24  Date: 07/10/09
[    0.620293] NET: Registered protocol family 16
[    0.620293] EISA bus registered
[    0.620293] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.620293] ACPI: bus type pci registered
[    0.620293] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[    0.620293] PCI: MCFG area at e0000000 reserved in E820
[    0.620293] PCI: Using MMCONFIG for extended config space
[    0.620293] PCI: Using configuration type 1 for base access
[    0.624237] ACPI: EC: Look up EC in DSDT
[    0.673744] ACPI: BIOS _OSI(Linux) query ignored
[    0.673749] ACPI: DMI System Vendor: Dell Inc.               
[    0.673753] ACPI: DMI Product Name: Dell DXP061                 
[    0.673757] ACPI: DMI Product Version:
[    0.673761] ACPI: DMI Board Name: 0WG855
[    0.673764] ACPI: DMI BIOS Vendor: Dell Inc.               
[    0.673768] ACPI: DMI BIOS Date: 11/30/2006
[    0.673771] ACPI: Please send DMI info above to linux-acpi@vger.kernel.org
[    0.673776] ACPI: If "acpi_osi=Linux" works better, please notify linux-acpi@vger.kernel.org
[    0.696856] ACPI: Interpreter enabled
[    0.696861] ACPI: (supports S0 S3 S4 S5)
[    0.696889] ACPI: Using IOAPIC for interrupt routing
[    0.793499] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.793499] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.793499] pci 0000:00:01.0: PME# disabled
[    0.793499] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[    0.793499] pci 0000:00:19.0: PME# disabled
[    0.793499] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[    0.793499] pci 0000:00:1a.7: PME# disabled
[    0.793499] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.793499] pci 0000:00:1b.0: PME# disabled
[    0.793499] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.793499] pci 0000:00:1c.0: PME# disabled
[    0.793499] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[    0.793499] pci 0000:00:1c.4: PME# disabled
[    0.793499] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.793499] pci 0000:00:1d.7: PME# disabled
[    0.793499] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
[    0.793499] pci 0000:00:1f.0: quirk: region 0880-08bf claimed by ICH6 GPIO
[    0.793499] pci 0000:00:1f.2: PME# supported from D3hot
[    0.793499] pci 0000:00:1f.2: PME# disabled
[    0.793499] PCI: bridge 0000:00:01.0 io port: [dfff0000d000, f7923e5800000122]
[    0.793499] PCI: bridge 0000:00:01.0 32bit mmio: [dfefffffdd000000, f7923e5800000122]
[    0.793499] PCI: bridge 0000:00:01.0 64bit mmio pref: [cfffffffc0000000, f7915000f7923e58]
[    0.793499] PCI: bridge 0000:00:1c.0 32bit mmio: [dcffffffdcf00000, f792565800000122]
[    0.793499] pci 0000:00:1e.0: transparent bridge
[    0.793499] bus 00 -> node 0
[    0.793499] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.796578] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI4._PRT]
[    0.797576] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2._PRT]
[    0.798254] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
[    0.798926] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI5._PRT]
[    1.814037] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15)
[    1.814037] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 15)
[    1.816714] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 12 15)
[    1.817471] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
[    1.818246] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12 15)
[    1.819009] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12 15)
[    1.819765] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 9 10 11 12 15)
[    1.820543] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 *4 5 6 7 9 10 11 12 15)
[    1.820750] Linux Plug and Play Support v0.97 (c) Adam Belay
[    1.820750] pnp: PnP ACPI init
[    1.820750] ACPI: bus type pnp registered
[    1.831275] pnp 00:01: io resource (0x800-0x85f) overlaps 0000:00:1f.0 BAR 7 (0x800-0x87f), disabling
[    1.831278] pnp 00:01: io resource (0x860-0x8ff) overlaps 0000:00:1f.0 BAR 7 (0x800-0x87f), disabling
[    1.869452] pnp: PnP ACPI: found 10 devices
[    1.869454] ACPI: ACPI bus type pnp unregistered
[    1.869458] PnPBIOS: Disabled by ACPI PNP
[    1.869473] PCI: Using ACPI for IRQ routing
[    1.876043] NET: Registered protocol family 8
[    1.876046] NET: Registered protocol family 20
[    1.876066] NetLabel: Initializing
[    1.876066] NetLabel:  domain hash size = 128
[    1.876066] NetLabel:  protocols = UNLABELED CIPSOv4
[    1.876081] NetLabel:  unlabeled traffic allowed by default
[    1.876089] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    1.876095] hpet0: 3 64-bit timers, 14318180 Hz
[    1.878819] tracer: 772 pages allocated for 65536 entries of 48 bytes
[    1.878821]    actual entries 65620
[    1.878902] AppArmor: AppArmor Filesystem Enabled
[    1.878921] ACPI: RTC can wake from S4
[    1.880047] Switched to high resolution mode on CPU 0
[    1.880490] Switched to high resolution mode on CPU 1
[    1.884050] system 00:01: ioport range 0xc00-0xc7f has been reserved
[    1.884064] system 00:07: iomem range 0x0-0x9ffff could not be reserved
[    1.884068] system 00:07: iomem range 0x100000-0xffffff could not be reserved
[    1.884072] system 00:07: iomem range 0x1000000-0xbfe53bff could not be reserved
[    1.884075] system 00:07: iomem range 0xf0000-0xfffff could not be reserved
[    1.884079] system 00:07: iomem range 0xc0000-0xd7fff could not be reserved
[    1.884083] system 00:07: iomem range 0xfec00000-0xfecfffff could not be reserved
[    1.884087] system 00:07: iomem range 0xfee00000-0xfeefffff could not be reserved
[    1.884090] system 00:07: iomem range 0xffb00000-0xffbfffff could not be reserved
[    1.884094] system 00:07: iomem range 0xffc00000-0xffffffff could not be reserved
[    1.884101] system 00:08: ioport range 0x100-0x1fe has been reserved
[    1.884105] system 00:08: ioport range 0x200-0x277 has been reserved
[    1.884108] system 00:08: ioport range 0x280-0x2e7 has been reserved
[    1.884112] system 00:08: ioport range 0x2e8-0x2ef has been reserved
[    1.884115] system 00:08: ioport range 0x2f0-0x2f7 has been reserved
[    1.884118] system 00:08: ioport range 0x2f8-0x2ff has been reserved
[    1.884122] system 00:08: ioport range 0x300-0x377 has been reserved
[    1.884125] system 00:08: ioport range 0x380-0x3bb has been reserved
[    1.884128] system 00:08: ioport range 0x3c0-0x3e7 could not be reserved
[    1.884132] system 00:08: ioport range 0x3f6-0x3f7 has been reserved
[    1.884135] system 00:08: ioport range 0x400-0x4cf has been reserved
[    1.884139] system 00:08: ioport range 0x4d2-0x57f has been reserved
[    1.884142] system 00:08: ioport range 0x580-0x677 has been reserved
[    1.884145] system 00:08: ioport range 0x680-0x777 has been reserved
[    1.884149] system 00:08: ioport range 0x780-0x7bb has been reserved
[    1.884152] system 00:08: ioport range 0x7c0-0x7ff has been reserved
[    1.884155] system 00:08: ioport range 0x8e0-0x8ff has been reserved
[    1.884159] system 00:08: ioport range 0x900-0x9fe has been reserved
[    1.884162] system 00:08: ioport range 0xa00-0xafe has been reserved
[    1.884166] system 00:08: ioport range 0xb00-0xbfe has been reserved
[    1.884169] system 00:08: ioport range 0xc80-0xcaf has been reserved
[    1.884172] system 00:08: ioport range 0xcb0-0xcbf has been reserved
[    1.884176] system 00:08: ioport range 0xcc0-0xcf7 has been reserved
[    1.884179] system 00:08: ioport range 0xd00-0xdfe has been reserved
[    1.884183] system 00:08: ioport range 0xe00-0xefe has been reserved
[    1.884186] system 00:08: ioport range 0xf00-0xffe has been reserved
[    1.884190] system 00:08: ioport range 0x2000-0x20fe has been reserved
[    1.884193] system 00:08: ioport range 0x2100-0x21fe has been reserved
[    1.884197] system 00:08: ioport range 0x2200-0x22fe has been reserved
[    1.884200] system 00:08: ioport range 0x2300-0x23fe has been reserved
[    1.884204] system 00:08: ioport range 0x2400-0x24fe has been reserved
[    1.884207] system 00:08: ioport range 0x2500-0x25fe has been reserved
[    1.884211] system 00:08: ioport range 0x2600-0x26fe has been reserved
[    1.884214] system 00:08: ioport range 0x2700-0x27fe has been reserved
[    1.884218] system 00:08: ioport range 0x2800-0x28fe has been reserved
[    1.884221] system 00:08: ioport range 0x2900-0x29fe has been reserved
[    1.884225] system 00:08: ioport range 0x2a00-0x2afe has been reserved
[    1.884228] system 00:08: ioport range 0x2b00-0x2bfe has been reserved
[    1.884232] system 00:08: ioport range 0x2c00-0x2cfe has been reserved
[    1.884236] system 00:08: ioport range 0x2d00-0x2dfe has been reserved
[    1.884239] system 00:08: ioport range 0x2e00-0x2efe has been reserved
[    1.884243] system 00:08: ioport range 0x2f00-0x2ffe has been reserved
[    1.884246] system 00:08: ioport range 0x5000-0x50fe has been reserved
[    1.884250] system 00:08: ioport range 0x5100-0x51fe has been reserved
[    1.884254] system 00:08: ioport range 0x5200-0x52fe has been reserved
[    1.884257] system 00:08: ioport range 0x5300-0x53fe has been reserved
[    1.884261] system 00:08: ioport range 0x5400-0x54fe has been reserved
[    1.884265] system 00:08: ioport range 0x5500-0x55fe has been reserved
[    1.884278] system 00:08: ioport range 0x5600-0x56fe has been reserved
[    1.884281] system 00:08: ioport range 0x5700-0x57fe has been reserved
[    1.884284] system 00:08: ioport range 0x5800-0x58fe has been reserved
[    1.884286] system 00:08: ioport range 0x5900-0x59fe has been reserved
[    1.884289] system 00:08: ioport range 0x5a00-0x5afe has been reserved
[    1.884292] system 00:08: ioport range 0x5b00-0x5bfe has been reserved
[    1.884295] system 00:08: ioport range 0x5c00-0x5cfe has been reserved
[    1.884300] system 00:08: ioport range 0x5d00-0x5dfe has been reserved
[    1.884303] system 00:08: ioport range 0x5e00-0x5efe has been reserved
[    1.884306] system 00:08: ioport range 0x5f00-0x5ffe has been reserved
[    1.884308] system 00:08: ioport range 0x6000-0x60fe has been reserved
[    1.884311] system 00:08: ioport range 0x6100-0x61fe has been reserved
[    1.884314] system 00:08: ioport range 0x6200-0x62fe has been reserved
[    1.884317] system 00:08: ioport range 0x6300-0x63fe has been reserved
[    1.884319] system 00:08: ioport range 0x6400-0x64fe has been reserved
[    1.884322] system 00:08: ioport range 0x6500-0x65fe has been reserved
[    1.884325] system 00:08: ioport range 0x6600-0x66fe has been reserved
[    1.884328] system 00:08: ioport range 0x6700-0x67fe has been reserved
[    1.884330] system 00:08: ioport range 0x6800-0x68fe has been reserved
[    1.884333] system 00:08: ioport range 0x6900-0x69fe has been reserved
[    1.884336] system 00:08: ioport range 0x6a00-0x6afe has been reserved
[    1.884339] system 00:08: ioport range 0x6b00-0x6bfe has been reserved
[    1.884341] system 00:08: ioport range 0x6c00-0x6cfe has been reserved
[    1.884344] system 00:08: ioport range 0x6d00-0x6dfe has been reserved
[    1.884347] system 00:08: ioport range 0x6e00-0x6efe has been reserved
[    1.884350] system 00:08: ioport range 0x6f00-0x6ffe has been reserved
[    1.884353] system 00:08: ioport range 0xa000-0xa0fe has been reserved
[    1.884356] system 00:08: ioport range 0xa100-0xa1fe has been reserved
[    1.884358] system 00:08: ioport range 0xa200-0xa2fe has been reserved
[    1.884361] system 00:08: ioport range 0xa300-0xa3fe has been reserved
[    1.884364] system 00:08: ioport range 0xa400-0xa4fe has been reserved
[    1.884367] system 00:08: ioport range 0xa500-0xa5fe has been reserved
[    1.884370] system 00:08: ioport range 0xa600-0xa6fe has been reserved
[    1.884372] system 00:08: ioport range 0xa700-0xa7fe has been reserved
[    1.884375] system 00:08: ioport range 0xa800-0xa8fe has been reserved
[    1.884378] system 00:08: ioport range 0xa900-0xa9fe has been reserved
[    1.884381] system 00:08: ioport range 0xaa00-0xaafe has been reserved
[    1.884384] system 00:08: ioport range 0xab00-0xabfe has been reserved
[    1.884387] system 00:08: ioport range 0xac00-0xacfe has been reserved
[    1.884389] system 00:08: ioport range 0xad00-0xadfe has been reserved
[    1.884392] system 00:08: ioport range 0xae00-0xaefe has been reserved
[    1.884395] system 00:08: ioport range 0xaf00-0xaffe has been reserved
[    1.884398] system 00:08: iomem range 0xe0000000-0xefffffff could not be reserved
[    1.884401] system 00:08: iomem range 0xfeda0000-0xfedacfff has been reserved
[    1.915014] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[    1.915017] pci 0000:00:01.0:   IO window: 0xd000-0xdfff
[    1.915021] pci 0000:00:01.0:   MEM window: 0xdd000000-0xdfefffff
[    1.915025] pci 0000:00:01.0:   PREFETCH window: 0x000000c0000000-0x000000cfffffff
[    1.915029] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[    1.915031] pci 0000:00:1c.0:   IO window: disabled
[    1.915036] pci 0000:00:1c.0:   MEM window: 0xdcf00000-0xdcffffff
[    1.915039] pci 0000:00:1c.0:   PREFETCH window: disabled
[    1.915045] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:03
[    1.915047] pci 0000:00:1c.4:   IO window: disabled
[    1.915051] pci 0000:00:1c.4:   MEM window: disabled
[    1.915055] pci 0000:00:1c.4:   PREFETCH window: disabled
[    1.915061] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:04
[    1.915063] pci 0000:00:1e.0:   IO window: disabled
[    1.915067] pci 0000:00:1e.0:   MEM window: disabled
[    1.915070] pci 0000:00:1e.0:   PREFETCH window: disabled
[    1.915085] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.915089] pci 0000:00:01.0: setting latency timer to 64
[    1.915096] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.915100] pci 0000:00:1c.0: setting latency timer to 64
[    1.915107] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.915111] pci 0000:00:1c.4: setting latency timer to 64
[    1.915118] pci 0000:00:1e.0: setting latency timer to 64
[    1.915121] bus: 00 index 0 io port: [ffff00000000, f7927e3cf7914c00]
[    1.915123] bus: 00 index 1 mmio: [ffffffff00000000, f7927e3cf7914c00]
[    1.915126] bus: 01 index 0 io port: [dfff0000d000, f7914c14f7923c00]
[    1.915128] bus: 01 index 1 mmio: [dfefffffdd000000, f7914c14f7923c00]
[    1.915130] bus: 01 index 2 mmio: [cfffffffc0000000, f7914c14f7923c00]
[    1.915133] bus: 01 index 3 mmio: [0, f7914c14f7923c00]
[    1.915135] bus: 02 index 0 mmio: [0, f7914c14f7925400]
[    1.915137] bus: 02 index 1 mmio: [dcffffffdcf00000, f7914c14f7925400]
[    1.915139] bus: 02 index 2 mmio: [0, f7914c14f7925400]
[    1.915141] bus: 02 index 3 mmio: [0, f7914c14f7925400]
[    1.915143] bus: 03 index 0 mmio: [0, f7914c14f7925800]
[    1.915145] bus: 03 index 1 mmio: [0, f7914c14f7925800]
[    1.915147] bus: 03 index 2 mmio: [0, f7914c14f7925800]
[    1.915149] bus: 03 index 3 mmio: [0, f7914c14f7925800]
[    1.915151] bus: 04 index 0 mmio: [0, f7914c14f7926c00]
[    1.915153] bus: 04 index 1 mmio: [0, f7914c14f7926c00]
[    1.915155] bus: 04 index 2 mmio: [0, f7914c14f7926c00]
[    1.915157] bus: 04 index 3 io port: [ffff00000000, f7914c14f7926c00]
[    1.915159] bus: 04 index 4 mmio: [ffffffff00000000, f7914c14f7926c00]
[    1.915167] NET: Registered protocol family 2
[    1.928099] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    1.928394] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    1.928726] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    1.928915] TCP: Hash tables configured (established 131072 bind 65536)
[    1.928918] TCP reno registered
[    1.936147] NET: Registered protocol family 1
[    1.936295] checking if image is initramfs... it is
[    2.607262] Freeing initrd memory: 8196k freed
[    2.607585] Simple Boot Flag at 0x7a set to 0x1
[    2.608358] audit: initializing netlink socket (disabled)
[    2.608382] type=2000 audit(1247252605.608:1): initialized
[    2.614029] highmem bounce pool size: 64 pages
[    2.614035] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    2.616212] VFS: Disk quotas dquot_6.5.1
[    2.616304] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    2.616406] msgmni has been set to 1725
[    2.616534] io scheduler noop registered
[    2.616537] io scheduler anticipatory registered
[    2.616540] io scheduler deadline registered
[    2.616551] io scheduler cfq registered (default)
[    2.616685] pci 0000:01:00.0: Boot video device
[    2.616785] pcieport-driver 0000:00:01.0: setting latency timer to 64
[    2.616816] pcieport-driver 0000:00:01.0: found MSI capability
[    2.616845] pci_express 0000:00:01.0:pcie00: allocate port service
[    2.616888] pci_express 0000:00:01.0:pcie03: allocate port service
[    2.616968] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[    2.616998] pcieport-driver 0000:00:1c.0: found MSI capability
[    2.617029] pci_express 0000:00:1c.0:pcie00: allocate port service
[    2.617072] pci_express 0000:00:1c.0:pcie02: allocate port service
[    2.617111] pci_express 0000:00:1c.0:pcie03: allocate port service
[    2.617194] pcieport-driver 0000:00:1c.4: setting latency timer to 64
[    2.617224] pcieport-driver 0000:00:1c.4: found MSI capability
[    2.617255] pci_express 0000:00:1c.4:pcie00: allocate port service
[    2.617295] pci_express 0000:00:1c.4:pcie02: allocate port service
[    2.617334] pci_express 0000:00:1c.4:pcie03: allocate port service
[    2.617643] isapnp: Scanning for PnP cards...
[    2.970565] isapnp: No Plug & Play device found
[    2.997061] hpet_resources: 0xfed00000 is busy
[    2.997108] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[    2.999077] brd: module loaded
[    2.999141] input: Macintosh mouse button emulation as /class/input/input0
[    2.999309] PNP: No PS/2 controller found. Probing ports directly.
[    3.001892] serio: i8042 KBD port at 0x60,0x64 irq 1
[    3.001898] serio: i8042 AUX port at 0x60,0x64 irq 12
[    3.004166] mice: PS/2 mouse device common for all mice
[    3.004328] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[    3.004350] rtc0: alarms up to one day, hpet irqs
[    3.004463] EISA: Probing bus 0 at eisa.0
[    3.004466] EISA: Cannot allocate resource for mainboard
[    3.004472] Cannot allocate resource for EISA slot 2
[    3.004481] Cannot allocate resource for EISA slot 5
[    3.004483] Cannot allocate resource for EISA slot 6
[    3.004492] EISA: Detected 0 cards.
[    3.004496] cpuidle: using governor ladder
[    3.004499] cpuidle: using governor menu
[    3.004833] aufs 20080609
[    3.005307] Using IPI No-Shortcut mode
[    3.005468] registered taskstats version 1
[    3.005591]   Magic number: 1:286:91
[    3.005682] rtc_cmos 00:05: setting system clock to 2009-07-10 19:03:26 UTC (1247252606)
[    3.005685] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    3.005687] EDD information not available.
[    3.005919] Freeing unused kernel memory: 428k freed
[    3.005944] Write protecting the kernel read-only data: 952k
[    3.165680] fuse init (API version 7.9)
[    3.290661] uvesafb: failed to execute /sbin/v86d
[    3.290665] uvesafb: make sure that the v86d helper is installed and executable
[    3.290668] uvesafb: Getting VBE info block failed (eax=0x4f00, err=-2)
[    3.290670] uvesafb: vbe_init() failed with -22
[    3.290676] uvesafb: probe of uvesafb.0 failed with error -22
[    3.332170] processor ACPI0007:00: registered as cooling_device0
[    3.332230] processor ACPI0007:01: registered as cooling_device1
[    3.939934] usbcore: registered new interface driver usbfs
[    3.939958] usbcore: registered new interface driver hub
[    3.957742] usbcore: registered new device driver usb
[    3.963276] e1000e: Intel(R) PRO/1000 Network Driver - 0.4.1.7
[    3.963279] e1000e: Copyright (c) 1999-2008 Intel Corporation.
[    3.963311] e1000e 0000:00:19.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[    3.963325] e1000e 0000:00:19.0: setting latency timer to 64
[    3.966375] USB Universal Host Controller Interface driver v3.0
[    4.008082] No dock devices found.
[    4.039466] SCSI subsystem initialized
[    4.053922] libata version 3.00 loaded.
[    4.258654] 0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:19:d1:21:a2:0f
[    4.258658] 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[    4.258680] 0000:00:19.0: eth0: MAC: 6, PHY: 6, PBA No: 1021ff-0ff
[    4.258775] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    4.258787] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[    4.258791] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[    4.258841] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[    4.258873] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000ff20
[    4.259023] usb usb1: configuration #1 chosen from 1 choice
[    4.259056] hub 1-0:1.0: USB hub found
[    4.259065] hub 1-0:1.0: 2 ports detected
[    4.468237] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    4.468246] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[    4.468250] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[    4.468286] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[    4.468312] uhci_hcd 0000:00:1a.1: irq 17, io base 0x0000ff00
[    4.468391] usb usb2: configuration #1 chosen from 1 choice
[    4.468417] hub 2-0:1.0: USB hub found
[    4.468424] hub 2-0:1.0: 2 ports detected
[    4.576022] usb 1-1: new full speed USB device using uhci_hcd and address 2
[    4.676231] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 22 (level, low) -> IRQ 22
[    4.676246] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[    4.676250] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[    4.676295] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 3
[    4.680188] ehci_hcd 0000:00:1a.7: debug port 1
[    4.680194] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[    4.680205] ehci_hcd 0000:00:1a.7: irq 22, io mem 0xdffdac00
[    4.700051] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    4.700148] usb usb3: configuration #1 chosen from 1 choice
[    4.700184] hub 3-0:1.0: USB hub found
[    4.700194] hub 3-0:1.0: 4 ports detected
[    4.908309] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    4.908328] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    4.908332] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    4.908361] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4
[    4.908388] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000ff80
[    4.908479] usb usb4: configuration #1 chosen from 1 choice
[    4.908505] hub 4-0:1.0: USB hub found
[    4.908512] hub 4-0:1.0: 2 ports detected
[    5.100020] usb 1-1: device not accepting address 2, error -71
[    5.116474] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    5.116481] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    5.116484] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    5.116631] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5
[    5.116653] uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000ff60
[    5.116864] usb usb5: configuration #1 chosen from 1 choice
[    5.116893] hub 5-0:1.0: USB hub found
[    5.116900] hub 5-0:1.0: 2 ports detected
[    5.156047] hub 1-0:1.0: unable to enumerate USB device on port 1
[    5.220503] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    5.220509] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    5.220513] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    5.220540] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6
[    5.220567] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ff40
[    5.220643] usb usb6: configuration #1 chosen from 1 choice
[    5.220668] hub 6-0:1.0: USB hub found
[    5.220674] hub 6-0:1.0: 2 ports detected
[    5.396023] usb 3-1: new high speed USB device using ehci_hcd and address 2
[    5.428508] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    5.428517] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    5.428520] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    5.428548] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
[    5.432457] ehci_hcd 0000:00:1d.7: debug port 1
[    5.432463] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[    5.432467] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xff980800
[    5.520031] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    5.520130] usb usb7: configuration #1 chosen from 1 choice
[    5.520164] hub 7-0:1.0: USB hub found
[    5.520172] hub 7-0:1.0: 6 ports detected
[    5.528669] usb 3-1: configuration #1 chosen from 1 choice
[    5.528960] hub 3-1:1.0: USB hub found
[    5.529002] hub 3-1:1.0: 4 ports detected
[    5.728209] ahci 0000:00:1f.2: version 3.0
[    5.728225] ahci 0000:00:1f.2: PCI INT C -> GSI 20 (level, low) -> IRQ 20
[    5.728358] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl RAID mode
[    5.728361] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ems
[    5.728365] ahci 0000:00:1f.2: setting latency timer to 64
[    5.728862] scsi0 : ahci
[    5.728950] scsi1 : ahci
[    5.729001] scsi2 : ahci
[    5.729051] scsi3 : ahci
[    5.729100] scsi4 : ahci
[    5.729682] scsi5 : ahci
[    5.729719] ata1: SATA max UDMA/133 abar m2048@0xff970000 port 0xff970100 irq 220
[    5.729722] ata2: SATA max UDMA/133 abar m2048@0xff970000 port 0xff970180 irq 220
[    5.729725] ata3: SATA max UDMA/133 abar m2048@0xff970000 port 0xff970200 irq 220
[    5.729728] ata4: SATA max UDMA/133 abar m2048@0xff970000 port 0xff970280 irq 220
[    5.729731] ata5: SATA max UDMA/133 abar m2048@0xff970000 port 0xff970300 irq 220
[    5.729734] ata6: SATA max UDMA/133 abar m2048@0xff970000 port 0xff970380 irq 220
[    6.048040] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    6.067843] ata1.00: ATA-7: WDC WD3200KS-75PFB0, 21.00M21, max UDMA/133
[    6.067847] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32)
[    6.068593] ata1.00: configured for UDMA/133
[    6.112034] usb 7-2: new high speed USB device using ehci_hcd and address 2
[    6.318174] usb 7-2: configuration #1 chosen from 1 choice
[    6.612180] usb 2-1: new full speed USB device using uhci_hcd and address 2
[    6.787733] usb 2-1: configuration #1 chosen from 1 choice
[    6.808038] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    6.841472] ata2.00: ATAPI: TSSTcorp DVD+/-RW TS-H553A, DE04, max UDMA/33
[    6.841475] ata2.00: applying bridge limits
[    6.875669] ata2.00: configured for UDMA/33
[    7.028022] usb 6-2: new low speed USB device using uhci_hcd and address 2
[    7.205996] usb 6-2: configuration #1 chosen from 1 choice
[    7.208057] ata3: SATA link down (SStatus 0 SControl 300)
[    7.544026] ata4: SATA link down (SStatus 0 SControl 300)
[    7.880036] ata5: SATA link down (SStatus 0 SControl 300)
[    8.216026] ata6: SATA link down (SStatus 0 SControl 300)
[    8.232192] scsi 0:0:0:0: Direct-Access     ATA      WDC WD3200KS-75P 21.0 PQ: 0 ANSI: 5
[    8.233482] scsi 1:0:0:0: CD-ROM            TSSTcorp DVD+-RW TS-H553A DE04 PQ: 0 ANSI: 5
[    8.268315] Driver 'sr' needs updating - please use bus_type methods
[    8.271182] Driver 'sd' needs updating - please use bus_type methods
[    8.271611] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[    8.271640] sd 0:0:0:0: [sda] Write Protect is off
[    8.271642] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    8.271680] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    8.271765] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[    8.271785] sd 0:0:0:0: [sda] Write Protect is off
[    8.271787] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    8.271823] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    8.271827]  sda: sda1 sda2 sda3
[    8.274637] sd 0:0:0:0: [sda] Attached SCSI disk
[    8.282495] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[    8.282500] Uniform CD-ROM driver Revision: 3.20
[    8.282577] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    8.287868] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    8.287906] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    8.333358] usbcore: registered new interface driver libusual
[    8.333360] usbcore: registered new interface driver hiddev
[    8.339441] Initializing USB Mass Storage driver...
[    8.339572] scsi6 : SCSI emulation for USB Mass Storage devices
[    8.340243] usb-storage: device found at 2
[    8.340245] usb-storage: waiting for device to settle before scanning
[    8.340279] scsi7 : SCSI emulation for USB Mass Storage devices
[    8.340647] usb-storage: device found at 2
[    8.340649] usb-storage: waiting for device to settle before scanning
[    8.349905] input: Logitech USB Receiver as /class/input/input1
[    8.353721] input,hidraw0: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:1d.2-2
[    8.382621] Fixing up Logitech keyboard report descriptor
[    8.383622] input: Logitech USB Receiver as /class/input/input2
[    8.383923] input,hiddev96,hidraw1: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1d.2-2
[    8.383960] usbcore: registered new interface driver usb-storage
[    8.383963] USB Mass Storage support registered.
[    8.384081] usbcore: registered new interface driver usbhid
[    8.384084] usbhid: v2.6:USB HID core driver
[    9.247807] loop: module loaded
[    9.261396] EXT3-fs: INFO: recovery required on readonly filesystem.
[    9.261399] EXT3-fs: write access will be enabled during recovery.
[    9.582033] kjournald starting.  Commit interval 5 seconds
[    9.582050] EXT3-fs: recovery complete.
[    9.582217] EXT3-fs: mounted filesystem with ordered data mode.
[   12.258397] udevd version 124 started
[   12.705998] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[   13.391504] usb-storage: device scan complete
[   13.391569] usb-storage: device scan complete
[   13.394832] scsi 6:0:0:0: Direct-Access     TEAC     USB   HS-CF Card 4.00 PQ: 0 ANSI: 0
[   13.395406] scsi 7:0:0:0: Direct-Access     040514   Flash Disk       7.78 PQ: 0 ANSI: 2
[   13.398452] scsi 6:0:0:1: Direct-Access     TEAC     USB   HS-xD/SM   4.00 PQ: 0 ANSI: 0
[   13.400392] sd 7:0:0:0: [sdb] 64000 512-byte hardware sectors (33 MB)
[   13.402452] scsi 6:0:0:2: Direct-Access     TEAC     USB   HS-MS Card 4.00 PQ: 0 ANSI: 0
[   13.405391] sd 7:0:0:0: [sdb] Write Protect is off
[   13.405393] sd 7:0:0:0: [sdb] Mode Sense: 03 00 00 00
[   13.405395] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[   13.405702] scsi 6:0:0:3: Direct-Access     TEAC     USB   HS-SD Card 4.00 PQ: 0 ANSI: 0
[   13.417400] sd 7:0:0:0: [sdb] 64000 512-byte hardware sectors (33 MB)
[   13.422404] sd 7:0:0:0: [sdb] Write Protect is off
[   13.422407] sd 7:0:0:0: [sdb] Mode Sense: 03 00 00 00
[   13.422410] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[   13.422414]  sdb: sdb1
[   13.428552] sd 7:0:0:0: [sdb] Attached SCSI removable disk
[   13.428704] sd 7:0:0:0: Attached scsi generic sg2 type 0
[   13.433154] sd 6:0:0:0: [sdc] Attached SCSI removable disk
[   13.433237] sd 6:0:0:0: Attached scsi generic sg3 type 0
[   13.438058] sd 6:0:0:1: [sdd] Attached SCSI removable disk
[   13.438172] sd 6:0:0:1: Attached scsi generic sg4 type 0
[   13.445899] sd 6:0:0:2: [sde] Attached SCSI removable disk
[   13.446023] sd 6:0:0:2: Attached scsi generic sg5 type 0
[   13.487704] Linux agpgart interface v0.103
[   13.494328] sd 6:0:0:3: [sdf] Attached SCSI removable disk
[   13.494455] sd 6:0:0:3: Attached scsi generic sg6 type 0
[   13.794486] input: Power Button (FF) as /class/input/input3
[   13.844368] ACPI: Power Button (FF) [PWRF]
[   13.844427] input: Power Button (CM) as /class/input/input4
[   13.872751] iTCO_vendor_support: vendor-support=0
[   13.874877] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[   13.874964] iTCO_wdt: failed to reset NO_REBOOT flag, reboot disabled by hardware
[   13.874973] iTCO_wdt: No card detected
[   13.908365] ACPI: Power Button (CM) [VBTN]
[   13.938404] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   14.001559] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   14.432693] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   14.432711] HDA Intel 0000:00:1b.0: setting latency timer to 64
[   15.276587] lp: driver loaded but no devices found
[   15.975096] EXT3 FS on loop0, internal journal
[   21.515613] Adding 488272k swap on /host/ubuntu/disks/swap.disk.  Priority:-1 extents:1 across:488272k
[   21.607449] type=1505 audit(1247249025.444:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=4136
[   21.749969] type=1505 audit(1247249025.588:3): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=4141
[   21.750136] type=1505 audit(1247249025.588:4): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=4141
[   21.853040] ip_tables: (C) 2000-2006 Netfilter Core Team
[   22.248724] ACPI: WMI: Mapper loaded
[   23.672110] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[   23.724305] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[   23.724312] apm: disabled - APM is not SMP safe.
[   23.897960] ppdev: user-space parallel port driver
[   26.196857] Bluetooth: Core ver 2.13
[   26.198177] NET: Registered protocol family 31
[   26.198181] Bluetooth: HCI device and connection manager initialized
[   26.198187] Bluetooth: HCI socket layer initialized
[   26.211298] Bluetooth: L2CAP ver 2.11
[   26.211303] Bluetooth: L2CAP socket layer initialized
[   26.323086] Bluetooth: RFCOMM socket layer initialized
[   26.323459] Bluetooth: RFCOMM TTY layer initialized
[   26.323463] Bluetooth: RFCOMM ver 1.10
[   28.401841] mtrr: type mismatch for c0000000,10000000 old: write-back new: write-combining
[   32.448895] 0000:00:19.0: eth0: Link is Up 100 Mbps Full Duplex, Flow Control: None
[   32.448902] 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[   32.533182] NET: Registered protocol family 17
[   35.718265] 0000:00:19.0: eth0: changing MTU from 1500 to 1492
[   37.272881] 0000:00:19.0: eth0: Link is Up 100 Mbps Full Duplex, Flow Control: None
[   37.272887] 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[   50.445301] NET: Registered protocol family 10
[   50.446278] lo: Disabled Privacy Extensions
[   60.676025] eth0: no IPv6 routers present


og her er output fra lspci i terminalen

Kode: Vælg alt

00:00.0 Host bridge: Intel Corporation 82P965/G965 Memory Controller Hub (rev 02)
00:01.0 PCI bridge: Intel Corporation 82P965/G965 PCI Express Root Port (rev 02)
00:19.0 Ethernet controller: Intel Corporation 82566DC Gigabit Network Connection (rev 02)
00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 02)
00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 02)
00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 02)
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02)
00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev f2)
00:1f.0 ISA bridge: Intel Corporation 82801HH (ICH8DH) LPC Interface Controller (rev 02)
00:1f.2 RAID bus controller: Intel Corporation 82801 SATA RAID Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02)
01:00.0 VGA compatible controller: nVidia Corporation G71 [GeForce 7900 GS] (rev a1)


Kan nogen se hvad der er galt?
Det er intrepid der er installeret hos hende, for jeg havde på daværende tidspunkt ikke nogen nyere cd.

[lath]

Kan ikke se hvad der er galt umiddeltbart, så lidt mere information er nødvendig:

Kommandoerne skal selvfølgelig udføres på hendes maskine. Opret en tekst fil (f.eks. netdata.txt) og gem filen på en USB flash pen. Husk derefter at højreklikke på ikon af USB drev, og vælge "afmonter arkiv" - vente til indhold er gemt, og så fjerne flashpen fra computeren - ellers er filen ikke altid gemt på USB flashen. Brug derefter en anden computer med netadgang til at kopiere indholdet af filen over på næste indlæg i denne tråd.

Hvad er resultatet af følgende terminal kommandoer? (Hot tip: shift tast + Ins tast indsætter tekst i terminal vinduet)

1)

Kode: Vælg alt

ifconfig

som lister netkonfigurationen.

2)

Kode: Vælg alt

cat /etc/resolv.conf

som lister DNS serverne som oversætte navne til IP adresser.
Min /etc/resolv.conf ser således ud:

# Generated by NetworkManager
nameserver 84.238.0.66
nameserver 84.238.1.4

Eksempel på DNS opslag på ubuntudanmrak.dk:

lars@lars-laptop:~$ host -a ubuntudanmark.dk
Trying "ubuntudanmark.dk"
;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 61913
;; flags: qr rd ra; QUERY: 1, ANSWER: 6, AUTHORITY: 3, ADDITIONAL: 4

;; QUESTION SECTION:
;ubuntudanmark.dk. IN ANY

;; ANSWER SECTION:
ubuntudanmark.dk. 10433 IN MX 10 mx-cluster2.one.com.
ubuntudanmark.dk. 10433 IN MX 10 mx-cluster1.one.com.
ubuntudanmark.dk. 7664 IN A 195.47.247.107
ubuntudanmark.dk. 53381 IN NS ns2.b-one.nu.
ubuntudanmark.dk. 53381 IN NS ns3.b-one.nu.
ubuntudanmark.dk. 53381 IN NS ns1.b-one.nu.

;; AUTHORITY SECTION:
ubuntudanmark.dk. 53381 IN NS ns1.b-one.nu.
ubuntudanmark.dk. 53381 IN NS ns3.b-one.nu.
ubuntudanmark.dk. 53381 IN NS ns2.b-one.nu.

;; ADDITIONAL SECTION:
mx-cluster1.one.com. 76267 IN A 91.198.169.10
ns1.b-one.nu. 69476 IN A 195.47.247.15
ns2.b-one.nu. 69476 IN A 195.47.247.12
ns3.b-one.nu. 70018 IN A 217.116.240.83

Received 281 bytes from 84.238.0.66#53 in 28 ms

3)
!: Denne kommando kan tage et par sekunder at udføre. Vær tålmodig!

Kode: Vælg alt

route

som viser gateway IP adressen (den IP adresse, hvor computeren skal sende udadgående Internet trafik, som ikke er til computere i det samme netværk som computereren er koblet på.)

4)

Kode: Vælg alt

pstree

som lister processer (programmer) i et træ af processer.

/Lars

[Lhademmor]

Hej lars.

Jeg kan ikke umiddelbart forstå hvad i alverden du ville kunne bruge ifconfig til - der er jo ikke fundet noget netkort, så den er naturligvis tom!

Anyway, her er kommandoerne:

ifconfig:

Kode: Vælg alt

eth0      Link encap:Ethernet  HWaddr 00:19:d1:21:a2:0f 
          inet6 addr: fe80::219:d1ff:fe21:a20f/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1492  Metric:1
          RX packets:4 errors:0 dropped:0 overruns:0 frame:0
          TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100
          RX bytes:2360 (2.3 KB)  TX bytes:2983 (2.9 KB)

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:7908 errors:0 dropped:0 overruns:0 frame:0
          TX packets:7908 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:395668 (395.6 KB)  TX bytes:395668 (395.6 KB)


resolv:

Kode: Vælg alt

# Generated by NetworkManager


route:

Kode: Vælg alt

Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface


pstree:

Kode: Vælg alt

init-+-NetworkManager---{NetworkManager}
     |-acpid
     |-anacron
     |-atd
     |-avahi-daemon---avahi-daemon
     |-bonobo-activati---{bonobo-activati}
     |-console-kit-dae---63*[{console-kit-dae}]
     |-cron
     |-cupsd
     |-2*[dbus-daemon]
     |-dbus-launch
     |-dd
     |-fast-user-switc
     |-gconfd-2
     |-gdm---gdm-+-Xorg
     |           `-x-session-manag-+-bluetooth-apple
     |                             |-evolution-alarm---{evolution-alarm}
     |                             |-gnome-keyring-d
     |                             |-gnome-panel
     |                             |-metacity
     |                             |-nautilus---{nautilus}
     |                             |-nm-applet
     |                             |-python
     |                             |-seahorse-agent
     |                             |-tracker-applet
     |                             |-trackerd---2*[{trackerd}]
     |                             |-update-notifier
     |                             `-{x-session-manag}
     |-gedit
     |-6*[getty]
     |-gnome-keyring-d
     |-gnome-power-man
     |-gnome-screensav
     |-gnome-settings--+-pulseaudio-+-gconf-helper
     |                 |            `-2*[{pulseaudio}]
     |                 `-{gnome-settings-}
     |-gnome-terminal-+-bash---pstree
     |                |-gnome-pty-helpe
     |                `-{gnome-terminal}
     |-gvfs-fuse-daemo---3*[{gvfs-fuse-daemo}]
     |-gvfs-gphoto2-vo
     |-gvfs-hal-volume---{gvfs-hal-volume}
     |-gvfsd
     |-gvfsd-burn
     |-gvfsd-trash---{gvfsd-trash}
     |-hald---hald-runner-+-hald-addon-acpi
     |                    |-hald-addon-inpu
     |                    `-6*[hald-addon-stor]
     |-hcid
     |-jockey-backend
     |-klogd
     |-mixer_applet2---{mixer_applet2}
     |-mount.ntfs
     |-nm-system-setti
     |-syslogd
     |-system-tools-ba
     |-trashapplet
     |-udevd
     `-wpa_supplicant


Hjælper det? Ellers overvejer jeg om jeg skulle prøve at installere karmic på den, og se om det fixer det, men jeg er lidt loren ved at installere alphaprogrammer på min mors computer...

Computeren har i øvrigt også andre problemer, Ubuntu vil f.eks. ikke slukke automatisk, men, igen, det kan være at det er blevet løst post-Intrepid.

[lath]

Hej lars.

Jeg kan ikke umiddelbart forstå hvad i alverden du ville kunne bruge ifconfig til - der er jo ikke fundet noget netkort, så den er naturligvis tom!

Anyway, her er kommandoerne:

ifconfig:

Kode: Vælg alt

eth0      Link encap:Ethernet  HWaddr 00:19:d1:21:a2:0f 
          inet6 addr: fe80::219:d1ff:fe21:a20f/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1492  Metric:1
          RX packets:4 errors:0 dropped:0 overruns:0 frame:0
          TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100
          RX bytes:2360 (2.3 KB)  TX bytes:2983 (2.9 KB)

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:7908 errors:0 dropped:0 overruns:0 frame:0
          TX packets:7908 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:395668 (395.6 KB)  TX bytes:395668 (395.6 KB)


resolv:

Kode: Vælg alt

# Generated by NetworkManager


route:

Kode: Vælg alt

Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface


pstree:

Kode: Vælg alt

init-+-NetworkManager---{NetworkManager}
     |-acpid
     |-anacron
     |-atd
     |-avahi-daemon---avahi-daemon
     |-bonobo-activati---{bonobo-activati}
     |-console-kit-dae---63*[{console-kit-dae}]
     |-cron
     |-cupsd
     |-2*[dbus-daemon]
     |-dbus-launch
     |-dd
     |-fast-user-switc
     |-gconfd-2
     |-gdm---gdm-+-Xorg
     |           `-x-session-manag-+-bluetooth-apple
     |                             |-evolution-alarm---{evolution-alarm}
     |                             |-gnome-keyring-d
     |                             |-gnome-panel
     |                             |-metacity
     |                             |-nautilus---{nautilus}
     |                             |-nm-applet
     |                             |-python
     |                             |-seahorse-agent
     |                             |-tracker-applet
     |                             |-trackerd---2*[{trackerd}]
     |                             |-update-notifier
     |                             `-{x-session-manag}
     |-gedit
     |-6*[getty]
     |-gnome-keyring-d
     |-gnome-power-man
     |-gnome-screensav
     |-gnome-settings--+-pulseaudio-+-gconf-helper
     |                 |            `-2*[{pulseaudio}]
     |                 `-{gnome-settings-}
     |-gnome-terminal-+-bash---pstree
     |                |-gnome-pty-helpe
     |                `-{gnome-terminal}
     |-gvfs-fuse-daemo---3*[{gvfs-fuse-daemo}]
     |-gvfs-gphoto2-vo
     |-gvfs-hal-volume---{gvfs-hal-volume}
     |-gvfsd
     |-gvfsd-burn
     |-gvfsd-trash---{gvfsd-trash}
     |-hald---hald-runner-+-hald-addon-acpi
     |                    |-hald-addon-inpu
     |                    `-6*[hald-addon-stor]
     |-hcid
     |-jockey-backend
     |-klogd
     |-mixer_applet2---{mixer_applet2}
     |-mount.ntfs
     |-nm-system-setti
     |-syslogd
     |-system-tools-ba
     |-trashapplet
     |-udevd
     `-wpa_supplicant


Hjælper det? Ellers overvejer jeg om jeg skulle prøve at installere karmic på den, og se om det fixer det, men jeg er lidt loren ved at installere alphaprogrammer på min mors computer...

Computeren har i øvrigt også andre problemer, Ubuntu vil f.eks. ikke slukke automatisk, men, igen, det kan være at det er blevet løst post-Intrepid.

1)
Vær sikker på at det rigtige ethernet kabel bruges - straight-through eller cross-over.

2)
Vær sikker på at kablet virkelig er tilsluttet - er plastic-anordningen på et ethernet stik i stykker kan stikket hoppe ud.

3)
Vær sikker på at hver ende at de 2 ethernet enheder kan snakke i samme hastighed (10 Mbit/s, 100 Mbit/s, eller 1 Gbit/s)

4)
Det ser ud til at dhclient processen ikke kører - og så virker automatisk tildeling (DHCP) af IP adresser, subnet adresse, DNS server IP adresser ikke.

Kig i Netwærk Configuration i System > Indstillinger menuen, Rediger fanebladet ud for eth0. Der skal være et flueben ud for "Connect Automatically".

/Lars

[Lhademmor]

1)
Vær sikker på at det rigtige ethernet kabel bruges - straight-through eller cross-over.

2)
Vær sikker på at kablet virkelig er tilsluttet - er plastic-anordningen på et ethernet stik i stykker kan stikket hoppe ud.

3)
Vær sikker på at hver ende at de 2 ethernet enheder kan snakke i samme hastighed (10 Mbit/s, 100 Mbit/s, eller 1 Gbit/s)

4)
Det ser ud til at dhclient processen ikke kører - og så virker automatisk tildeling (DHCP) af IP adresser, subnet adresse, DNS server IP adresser ikke.

Kig i Netwærk Configuration i System > Indstillinger menuen, Rediger fanebladet ud for eth0. Der skal være et flueben ud for "Connect Automatically".

/Lars

1, 2 og 3 vælger jeg altså at ignorere for som jeg allerede har skrevet så virker det upåklageligt i Windows XP, så en sådanne fejl er udelukket. 4'eren ser jeg på snarest.

[thomasjohansen]

evt. prøv at opsætte eth0 manuelt i den dertil hørende config fil.

dette gøres sådan:

Kode: Vælg alt

sudo gedit /etc/network/interfaces

så kan du tilføje følgende i denne:

Kode: Vælg alt

auto lo
iface lo inet loopback
address 127.0.0.1


iface eth0 inet static
address 192.168.0.50
netmask 255.255.255.0


auto eth0

Gem og luk

genstart eth0 netværksopsætningen

Kode: Vælg alt

sudo /etc/init.d/networking restart

derefter prøv at lave en køre en ifconfig og en ping for at se om det virker.

ifconfig skulle gerne give et lign. resultat:

Kode: Vælg alt

eth0    Link encap:Ethernet  HWaddr 00:1f:29:d1:3f:c8 
          inet addr:192.168.0.50  Bcast:192.168.0.255  Mask:255.255.255.0
          inet6 addr: fe80::21f:29ff:fed1:3fc8/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:4399737 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1139913 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:271666568 (259.0 MB)  TX bytes:336028490 (320.4 MB)


Hvis det ikke hjælper kan du prøve at ændre config filen til at køre som dhcp ved at skrive følgende:

Kode: Vælg alt

sudo gedit /etc/network/interfaces

så kan du tilføje følgende i denne:

Kode: Vælg alt

auto lo
iface lo inet loopback
address 127.0.0.1


iface eth0 inet dhcp

auto eth0

Gem og luk

genstart eth0 netværksopsætningen

Kode: Vælg alt

sudo /etc/init.d/networking restart

Nogle gange når jeg har fået "rodet" godt og gevaldigt med netværksopsætningen bruger jeg følgende til kommandoer til at få nulstillet det:

Kode: Vælg alt

sudo ifconfig eth0 0.0.0.0 promisc


og

Kode: Vælg alt

sudo dhclient3 eth0