Sluk knappen har ingen funktion ? HP G5050EO

[MrDong]

Hej Igen
Med et nyt problem bare på anden bærbar computer.

Har en HP G5050EO med 2GB Ram 40 GB harddisk side by side med Windows Vista
Hvor jeg har installeret Ubuntu 15.04.

Jeg har så det problem når jeg skal lukke ned enten via knap ell sluk i programmet Logout når vi kun til , sidste linje er [ 2712.908301] sd 2:0:0:0 : [sda] Stopping disk
Mere sker der så ikke den lukke ikke helt ned, er der nogen der kan have et bud hvad jeg skal gøre ved dette problem ?

Mange Tak

[AJenbo]

<det kunne være et problem om kring strøm styring

prøv at give os resultatet ef dmesg lige efter du har tænt maskinen

[MrDong]

Kode: Vælg alt

[    0.000000] RAMDISK: [mem 0x35900000-0x36c77fff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x000F6510 000014 (v00 PTLTD )
[    0.000000] ACPI: RSDT 0x7F68CBDA 00004C (v01 HPQOEM SLIC-MPC 06040000  LTP 00000000)
[    0.000000] ACPI: FACP 0x7F693C86 000074 (v01 HP     NISSAN   06040000 LOHR 0000005A)
[    0.000000] ACPI: DSDT 0x7F68D506 006780 (v01 HP     NISSAN   06040000 INTL 20060608)
[    0.000000] ACPI: FACS 0x7F694FC0 000040
[    0.000000] ACPI: APIC 0x7F693CFA 000068 (v01 HP     NISSAN   06040000 LOHR 0000005A)
[    0.000000] ACPI: HPET 0x7F693D62 000038 (v01 HP     NISSAN   06040000 LOHR 0000005A)
[    0.000000] ACPI: MCFG 0x7F693D9A 00003C (v01 HP     NISSAN   06040000 LOHR 0000005A)
[    0.000000] ACPI: BOOT 0x7F693FD8 000028 (v01 PTLTD  $SBFTBL$ 06040000  LTP 00000001)
[    0.000000] ACPI: SLIC 0x7F693E08 000176 (v01 HPQOEM SLIC-MPC 06040000 LOHR 00000000)
[    0.000000] ACPI: APIC 0x7F693F7E 00005A (v01 PTLTD  ? APIC   06040000  LTP 00000000)
[    0.000000] ACPI: SSDT 0x7F68D2F8 00020A (v01 SataRe SataAhci 00001000 INTL 20060217)
[    0.000000] ACPI: SSDT 0x7F68D11C 0001DC (v01 PmRef  Cpu0Cst  00003001 INTL 20060217)
[    0.000000] ACPI: SSDT 0x7F68CC26 0004F6 (v01 PmRef  CpuPm    00003000 INTL 20060217)
[    0.000000] ACPI: BIOS bug: multiple APIC/MADT found, using 0
[    0.000000] ACPI: If "acpi_apic_instance=2" works better, notify linux-acpi@vger.kernel.org
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] 1146MB HIGHMEM available.
[    0.000000] 891MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 37bfe000
[    0.000000]   low ram: 0 - 37bfe000
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00001000-0x00ffffff]
[    0.000000]   Normal   [mem 0x01000000-0x37bfdfff]
[    0.000000]   HighMem  [mem 0x37bfe000-0x7f67ffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00001000-0x0009efff]
[    0.000000]   node   0: [mem 0x00100000-0x7f67ffff]
[    0.000000] Initmem setup node 0 [mem 0x00001000-0x7f67ffff]
[    0.000000] On node 0 totalpages: 521758
[    0.000000]   DMA zone: 40 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3998 pages, LIFO batch:0
[    0.000000]   Normal zone: 2190 pages used for memmap
[    0.000000]   Normal zone: 224254 pages, LIFO batch:31
[    0.000000]   HighMem zone: 293506 pages, LIFO batch:31
[    0.000000] Using APIC driver default
[    0.000000] Reserving Intel graphics stolen memory at 0x7f800000-0x7fffffff
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] smpboot: Allowing 2 CPUs, 1 hotplug CPUs
[    0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[    0.000000] e820: [mem 0x80000000-0xdfffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
[    0.000000] PERCPU: Embedded 17 pages/cpu @f6cb5000 s40320 r0 d29312 u69632
[    0.000000] pcpu-alloc: s40320 r0 d29312 u69632 alloc=17*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 519528
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.19.0-31-generic root=UUID=808d28df-5fa0-4731-aecd-53bc697b7ca2 ro quiet splash vt.handoff=7
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Initializing CPU#0
[    0.000000] Initializing HighMem for node 0 (00037bfe:0007f680)
[    0.000000] Initializing Movable for node 0 (00000000:00000000)
[    0.000000] Memory: 2032800K/2087032K available (7118K kernel code, 711K rwdata, 3008K rodata, 892K init, 796K bss, 54232K reserved, 0K cma-reserved, 1174024K highmem)
[    0.000000] virtual kernel memory layout:
    fixmap  : 0xfff15000 - 0xfffff000   ( 936 kB)
    pkmap   : 0xffc00000 - 0xffe00000   (2048 kB)
    vmalloc : 0xf83fe000 - 0xffbfe000   ( 120 MB)
    lowmem  : 0xc0000000 - 0xf7bfe000   ( 891 MB)
      .init : 0xc1a99000 - 0xc1b78000   ( 892 kB)
      .data : 0xc16f3f02 - 0xc1a97cc0   (3727 kB)
      .text : 0xc1000000 - 0xc16f3f02   (7119 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]    RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000]    RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:2304 nr_irqs:440 16
[    0.000000] CPU 0 irqstacks, hard=f4c36000 soft=f4c38000
[    0.000000] vt handoff: transparent VT on vt#7
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 1595.915 MHz processor
[    0.004015] Calibrating delay loop (skipped), value calculated using timer frequency.. 3191.83 BogoMIPS (lpj=6383660)
[    0.004020] pid_max: default: 32768 minimum: 301
[    0.004032] ACPI: Core revision 20141107
[    0.013624] ACPI: All ACPI Tables successfully acquired
[    0.013655] Security Framework initialized
[    0.013679] AppArmor: AppArmor initialized
[    0.013681] Yama: becoming mindful.
[    0.013745] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.013749] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.014149] Initializing cgroup subsys memory
[    0.014160] Initializing cgroup subsys devices
[    0.014165] Initializing cgroup subsys freezer
[    0.014170] Initializing cgroup subsys net_cls
[    0.014175] Initializing cgroup subsys blkio
[    0.014180] Initializing cgroup subsys perf_event
[    0.014185] Initializing cgroup subsys net_prio
[    0.014189] Initializing cgroup subsys hugetlb
[    0.014219] Disabled fast string operations
[    0.014227] mce: CPU supports 6 MCE banks
[    0.014237] CPU0: Thermal monitoring handled by SMI
[    0.014241] process: using mwait in idle threads
[    0.014251] Last level iTLB entries: 4KB 128, 2MB 4, 4MB 4
Last level dTLB entries: 4KB 256, 2MB 0, 4MB 32, 1GB 0
[    0.032015] ftrace: allocating 29423 entries in 58 pages
[    0.044145] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.044628] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.085188] smpboot: CPU0: Intel(R) Celeron(R) M CPU        520  @ 1.60GHz (fam: 06, model: 16, stepping: 01)
[    0.088000] Performance Events: PEBS fmt0-, 4-deep LBR, Core2 events, Intel PMU driver.
[    0.088000] ... version:                2
[    0.088000] ... bit width:              40
[    0.088000] ... generic registers:      2
[    0.088000] ... value mask:             000000ffffffffff
[    0.088000] ... max period:             000000007fffffff
[    0.088000] ... fixed-purpose events:   3
[    0.088000] ... event mask:             0000000700000003
[    0.088000] x86: Booted up 1 node, 1 CPUs
[    0.088000] smpboot: Total of 1 processors activated (3191.83 BogoMIPS)
[    0.088000] devtmpfs: initialized
[    0.088000] evm: security.selinux
[    0.088000] evm: security.SMACK64
[    0.088000] evm: security.SMACK64EXEC
[    0.088000] evm: security.SMACK64TRANSMUTE
[    0.088000] evm: security.SMACK64MMAP
[    0.088000] evm: security.ima
[    0.088000] evm: security.capability
[    0.088000] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.088000] PM: Registering ACPI NVS region [mem 0x7f680000-0x7f6fffff] (524288 bytes)
[    0.088046] pinctrl core: initialized pinctrl subsystem
[    0.088271] RTC time:  2:13:24, date: 01/07/16
[    0.088457] NET: Registered protocol family 16
[    0.088903] EISA bus registered
[    0.088910] cpuidle: using governor ladder
[    0.088914] cpuidle: using governor menu
[    0.089076] ACPI: bus type PCI registered
[    0.089080] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.089229] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.089233] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[    0.089235] PCI: Using MMCONFIG for extended config space
[    0.089237] PCI: Using configuration type 1 for base access
[    0.093239] ACPI: Added _OSI(Module Device)
[    0.093244] ACPI: Added _OSI(Processor Device)
[    0.093246] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.093249] ACPI: Added _OSI(Processor Aggregator Device)
[    0.096535] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[    0.097454] ACPI: Interpreter enabled
[    0.097478] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20141107/hwxface-580)
[    0.097484] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20141107/hwxface-580)
[    0.097504] ACPI: (supports S0 S3 S4 S5)
[    0.097507] ACPI: Using IOAPIC for interrupt routing
[    0.097557] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.156073] ACPI : EC: GPE storm detected(9 GPEs), transactions will use polling mode
[    0.197845] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.197856] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.197864] acpi PNP0A08:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[    0.198810] PCI host bridge to bus 0000:00
[    0.198816] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.198820] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7]
[    0.198823] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff]
[    0.198827] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.198831] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff]
[    0.198834] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff]
[    0.198837] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff]
[    0.198840] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff]
[    0.198843] pci_bus 0000:00: root bus resource [mem 0x80000000-0xfebfffff]
[    0.198859] pci 0000:00:00.0: [8086:27a0] type 00 class 0x060000
[    0.199028] pci 0000:00:02.0: [8086:27a2] type 00 class 0x030000
[    0.199046] pci 0000:00:02.0: reg 0x10: [mem 0xd0200000-0xd027ffff]
[    0.199055] pci 0000:00:02.0: reg 0x14: [io  0x1800-0x1807]
[    0.199064] pci 0000:00:02.0: reg 0x18: [mem 0xc0000000-0xcfffffff pref]
[    0.199073] pci 0000:00:02.0: reg 0x1c: [mem 0xd0300000-0xd033ffff]
[    0.199237] pci 0000:00:02.1: [8086:27a6] type 00 class 0x038000
[    0.199251] pci 0000:00:02.1: reg 0x10: [mem 0xd0280000-0xd02fffff]
[    0.199474] pci 0000:00:1b.0: [8086:27d8] type 00 class 0x040300
[    0.199504] pci 0000:00:1b.0: reg 0x10: [mem 0xd0340000-0xd0343fff 64bit]
[    0.199635] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.199789] pci 0000:00:1c.0: [8086:27d0] type 01 class 0x060400
[    0.199919] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.200083] pci 0000:00:1c.2: [8086:27d4] type 01 class 0x060400
[    0.200213] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[    0.200372] pci 0000:00:1d.0: [8086:27c8] type 00 class 0x0c0300
[    0.200435] pci 0000:00:1d.0: reg 0x20: [io  0x1820-0x183f]
[    0.200585] pci 0000:00:1d.1: [8086:27c9] type 00 class 0x0c0300
[    0.200649] pci 0000:00:1d.1: reg 0x20: [io  0x1840-0x185f]
[    0.200802] pci 0000:00:1d.2: [8086:27ca] type 00 class 0x0c0300
[    0.200865] pci 0000:00:1d.2: reg 0x20: [io  0x1860-0x187f]
[    0.201030] pci 0000:00:1d.7: [8086:27cc] type 00 class 0x0c0320
[    0.201058] pci 0000:00:1d.7: reg 0x10: [mem 0xd0544000-0xd05443ff]
[    0.201180] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.201330] pci 0000:00:1e.0: [8086:2448] type 01 class 0x060401
[    0.201543] pci 0000:00:1f.0: [8086:27b9] type 00 class 0x060100
[    0.201670] pci 0000:00:1f.0: can't claim BAR 13 [io  0x1000-0x107f]: address conflict with ACPI CPU throttle [io  0x1010-0x1015]
[    0.201679] pci 0000:00:1f.0: quirk: [io  0x1180-0x11bf] claimed by ICH6 GPIO
[    0.201851] pci 0000:00:1f.1: [8086:27df] type 00 class 0x01018a
[    0.201872] pci 0000:00:1f.1: reg 0x10: [io  0x0000-0x0007]
[    0.201886] pci 0000:00:1f.1: reg 0x14: [io  0x0000-0x0003]
[    0.201900] pci 0000:00:1f.1: reg 0x18: [io  0x0000-0x0007]
[    0.201914] pci 0000:00:1f.1: reg 0x1c: [io  0x0000-0x0003]
[    0.201928] pci 0000:00:1f.1: reg 0x20: [io  0x1810-0x181f]
[    0.201958] pci 0000:00:1f.1: legacy IDE quirk: reg 0x10: [io  0x01f0-0x01f7]
[    0.201961] pci 0000:00:1f.1: legacy IDE quirk: reg 0x14: [io  0x03f6]
[    0.201964] pci 0000:00:1f.1: legacy IDE quirk: reg 0x18: [io  0x0170-0x0177]
[    0.201967] pci 0000:00:1f.1: legacy IDE quirk: reg 0x1c: [io  0x0376]
[    0.202103] pci 0000:00:1f.2: [8086:27c5] type 00 class 0x010601
[    0.202131] pci 0000:00:1f.2: reg 0x10: [io  0x18b0-0x18b7]
[    0.202145] pci 0000:00:1f.2: reg 0x14: [io  0x18a4-0x18a7]
[    0.202159] pci 0000:00:1f.2: reg 0x18: [io  0x18a8-0x18af]
[    0.202173] pci 0000:00:1f.2: reg 0x1c: [io  0x18a0-0x18a3]
[    0.202187] pci 0000:00:1f.2: reg 0x20: [io  0x1890-0x189f]
[    0.202202] pci 0000:00:1f.2: reg 0x24: [mem 0xd0544400-0xd05447ff]
[    0.202269] pci 0000:00:1f.2: PME# supported from D3hot
[    0.202413] pci 0000:00:1f.3: [8086:27da] type 00 class 0x0c0500
[    0.202494] pci 0000:00:1f.3: reg 0x20: [io  0x18c0-0x18df]
[    0.202805] acpiphp: Slot [1] registered
[    0.202814] pci 0000:00:1c.0: PCI bridge to [bus 01]
[    0.202821] pci 0000:00:1c.0:   bridge window [io  0x0000-0x0fff]
[    0.202827] pci 0000:00:1c.0:   bridge window [mem 0x00000000-0x000fffff]
[    0.203041] pci 0000:06:00.0: [14e4:4311] type 00 class 0x028000
[    0.203119] pci 0000:06:00.0: reg 0x10: [mem 0xd0000000-0xd0003fff]
[    0.203668] pci 0000:06:00.0: supports D1 D2
[    0.203826] pci 0000:06:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.203855] pci 0000:00:1c.2: PCI bridge to [bus 06]
[    0.203862] pci 0000:00:1c.2:   bridge window [io  0x0000-0x0fff]
[    0.203869] pci 0000:00:1c.2:   bridge window [mem 0x00000000-0x000fffff]
[    0.203996] pci 0000:08:08.0: [10ec:8139] type 00 class 0x020000
[    0.204032] pci 0000:08:08.0: reg 0x10: [io  0x2000-0x20ff]
[    0.204049] pci 0000:08:08.0: reg 0x14: [mem 0xd0100000-0xd01000ff]
[    0.204166] pci 0000:08:08.0: supports D1 D2
[    0.204169] pci 0000:08:08.0: PME# supported from D1 D2 D3hot D3cold
[    0.204226] pci 0000:08:08.0: System wakeup disabled by ACPI
[    0.204361] pci 0000:00:1e.0: PCI bridge to [bus 08] (subtractive decode)
[    0.204368] pci 0000:00:1e.0:   bridge window [io  0x2000-0x2fff]
[    0.204375] pci 0000:00:1e.0:   bridge window [mem 0xd0100000-0xd01fffff]
[    0.204385] pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    0.204388] pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.204392] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.204395] pci 0000:00:1e.0:   bridge window [mem 0x000d0000-0x000d3fff] (subtractive decode)
[    0.204398] pci 0000:00:1e.0:   bridge window [mem 0x000d4000-0x000d7fff] (subtractive decode)
[    0.204402] pci 0000:00:1e.0:   bridge window [mem 0x000d8000-0x000dbfff] (subtractive decode)
[    0.204405] pci 0000:00:1e.0:   bridge window [mem 0x000dc000-0x000dffff] (subtractive decode)
[    0.204408] pci 0000:00:1e.0:   bridge window [mem 0x80000000-0xfebfffff] (subtractive decode)
[    0.204441] pci_bus 0000:00: on NUMA node 0
[    0.204611] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[    0.204700] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 *4 5 6 7 11 12 14 15)
[    0.204786] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 *3 4 5 6 7 10 12 14 15)
[    0.204870] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[    0.204955] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[    0.205044] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[    0.205129] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 *7 10 12 14 15)
[    0.205214] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 *5 6 7 11 12 14 15)
[    0.244513] ACPI: Enabled 3 GPEs in block 00 to 1F
[    0.244567] ACPI : EC: GPE = 0x19, I/O: command/status = 0x66, data = 0x62
[    0.244780] vgaarb: setting as boot device: PCI:0000:00:02.0
[    0.244784] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[    0.244789] vgaarb: loaded
[    0.244791] vgaarb: bridge control possible 0000:00:02.0
[    0.245397] SCSI subsystem initialized
[    0.245485] libata version 3.00 loaded.
[    0.245553] ACPI: bus type USB registered
[    0.245603] usbcore: registered new interface driver usbfs
[    0.245631] usbcore: registered new interface driver hub
[    0.245659] usbcore: registered new device driver usb
[    0.245939] PCI: Using ACPI for IRQ routing
[    0.257808] PCI: pci_cache_line_size set to 64 bytes
[    0.257831] pci 0000:06:00.0: can't claim BAR 0 [mem 0xd0000000-0xd0003fff]: no compatible bridge window
[    0.257887] e820: reserve RAM buffer [mem 0x0009f800-0x0009ffff]
[    0.257891] e820: reserve RAM buffer [mem 0x7f680000-0x7fffffff]
[    0.258156] NetLabel: Initializing
[    0.258159] NetLabel:  domain hash size = 128
[    0.258161] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.258179] NetLabel:  unlabeled traffic allowed by default
[    0.258397] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.258405] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.258411] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.260086] Switched to clocksource hpet
[    0.271379] AppArmor: AppArmor Filesystem Enabled
[    0.271541] pnp: PnP ACPI init
[    0.271788] system 00:00: [mem 0xe0000000-0xefffffff] has been reserved
[    0.271793] system 00:00: [mem 0xfed14000-0xfed17fff] has been reserved
[    0.271797] system 00:00: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.271801] system 00:00: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.271805] system 00:00: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.271808] system 00:00: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.271812] system 00:00: [mem 0xfed40000-0xfed44fff] has been reserved
[    0.271816] system 00:00: [mem 0xfed45000-0xfed8ffff] has been reserved
[    0.271822] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.312187] system 00:01: [mem 0xfed00000-0xfed003ff] has been reserved
[    0.312193] system 00:01: Plug and Play ACPI device, IDs PNP0103 PNP0c01 (active)
[    0.312292] system 00:02: [io  0x0800-0x080f] has been reserved
[    0.312297] system 00:02: [io  0x1000-0x107f] could not be reserved
[    0.312301] system 00:02: [io  0x1180-0x11bf] has been reserved
[    0.312305] system 00:02: [io  0x1640-0x164f] has been reserved
[    0.312309] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.312392] pnp 00:03: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.312475] pnp 00:04: Plug and Play ACPI device, IDs SYN011f SYN0100 SYN0002 PNP0f13 (active)
[    0.312558] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.312587] pnp: PnP ACPI: found 6 devices
[    0.312597] PnPBIOS: Disabled by ACPI PNP
[    0.350942] pci 0000:00:1c.0: bridge window [io  0x1000-0x0fff] to [bus 01] add_size 1000
[    0.350949] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000
[    0.350954] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 01] add_size 200000
[    0.350973] pci 0000:00:1c.2: bridge window [io  0x1000-0x0fff] to [bus 06] add_size 1000
[    0.350978] pci 0000:00:1c.2: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 06] add_size 200000
[    0.350983] pci 0000:00:1c.2: bridge window [mem 0x00100000-0x001fffff] to [bus 06] add_size 200000
[    0.351002] pci 0000:00:1f.0: BAR 13: [io  0x1000-0x107f] has bogus alignment
[    0.351008] pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[    0.351012] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[    0.351015] pci 0000:00:1c.2: res[14]=[mem 0x00100000-0x001fffff] get_res_add_size add_size 200000
[    0.351019] pci 0000:00:1c.2: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[    0.351023] pci 0000:00:1c.0: res[13]=[io  0x1000-0x0fff] get_res_add_size add_size 1000
[    0.351026] pci 0000:00:1c.2: res[13]=[io  0x1000-0x0fff] get_res_add_size add_size 1000
[    0.351038] pci 0000:00:1c.0: BAR 14: assigned [mem 0x80000000-0x801fffff]
[    0.351049] pci 0000:00:1c.0: BAR 15: assigned [mem 0x80200000-0x803fffff 64bit pref]
[    0.351056] pci 0000:00:1c.2: BAR 14: assigned [mem 0x80400000-0x806fffff]
[    0.351066] pci 0000:00:1c.2: BAR 15: assigned [mem 0x80700000-0x808fffff 64bit pref]
[    0.351073] pci 0000:00:1c.0: BAR 13: assigned [io  0x3000-0x3fff]
[    0.351078] pci 0000:00:1c.2: BAR 13: assigned [io  0x4000-0x4fff]
[    0.351082] pci 0000:00:1c.0: PCI bridge to [bus 01]
[    0.351087] pci 0000:00:1c.0:   bridge window [io  0x3000-0x3fff]
[    0.351095] pci 0000:00:1c.0:   bridge window [mem 0x80000000-0x801fffff]
[    0.351101] pci 0000:00:1c.0:   bridge window [mem 0x80200000-0x803fffff 64bit pref]
[    0.351113] pci 0000:06:00.0: BAR 0: assigned [mem 0x80400000-0x80403fff]
[    0.351121] pci 0000:00:1c.2: PCI bridge to [bus 06]
[    0.351125] pci 0000:00:1c.2:   bridge window [io  0x4000-0x4fff]
[    0.351133] pci 0000:00:1c.2:   bridge window [mem 0x80400000-0x806fffff]
[    0.351139] pci 0000:00:1c.2:   bridge window [mem 0x80700000-0x808fffff 64bit pref]
[    0.351149] pci 0000:00:1e.0: PCI bridge to [bus 08]
[    0.351154] pci 0000:00:1e.0:   bridge window [io  0x2000-0x2fff]
[    0.351161] pci 0000:00:1e.0:   bridge window [mem 0xd0100000-0xd01fffff]
[    0.351175] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.351179] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.351182] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.351185] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff]
[    0.351188] pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff]
[    0.351192] pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff]
[    0.351195] pci_bus 0000:00: resource 10 [mem 0x000dc000-0x000dffff]
[    0.351198] pci_bus 0000:00: resource 11 [mem 0x80000000-0xfebfffff]
[    0.351202] pci_bus 0000:01: resource 0 [io  0x3000-0x3fff]
[    0.351205] pci_bus 0000:01: resource 1 [mem 0x80000000-0x801fffff]
[    0.351209] pci_bus 0000:01: resource 2 [mem 0x80200000-0x803fffff 64bit pref]
[    0.351212] pci_bus 0000:06: resource 0 [io  0x4000-0x4fff]
[    0.351216] pci_bus 0000:06: resource 1 [mem 0x80400000-0x806fffff]
[    0.351219] pci_bus 0000:06: resource 2 [mem 0x80700000-0x808fffff 64bit pref]
[    0.351222] pci_bus 0000:08: resource 0 [io  0x2000-0x2fff]
[    0.351226] pci_bus 0000:08: resource 1 [mem 0xd0100000-0xd01fffff]
[    0.351229] pci_bus 0000:08: resource 4 [io  0x0000-0x0cf7]
[    0.351232] pci_bus 0000:08: resource 5 [io  0x0d00-0xffff]
[    0.351235] pci_bus 0000:08: resource 6 [mem 0x000a0000-0x000bffff]
[    0.351239] pci_bus 0000:08: resource 7 [mem 0x000d0000-0x000d3fff]
[    0.351242] pci_bus 0000:08: resource 8 [mem 0x000d4000-0x000d7fff]
[    0.351245] pci_bus 0000:08: resource 9 [mem 0x000d8000-0x000dbfff]
[    0.351248] pci_bus 0000:08: resource 10 [mem 0x000dc000-0x000dffff]
[    0.351251] pci_bus 0000:08: resource 11 [mem 0x80000000-0xfebfffff]
[    0.351302] NET: Registered protocol family 2
[    0.351657] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.351678] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.351716] TCP: Hash tables configured (established 8192 bind 8192)
[    0.351764] TCP: reno registered
[    0.351767] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.351778] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.351850] NET: Registered protocol family 1
[    0.351877] pci 0000:00:02.0: Video device with shadowed ROM
[    1.952020] pci 0000:00:1d.7: EHCI: BIOS handoff failed (BIOS bug?) 01010001
[    1.952215] PCI: CLS 64 bytes, default 64
[    1.952303] Trying to unpack rootfs image as initramfs...
[    2.512567] Freeing initrd memory: 19936K (f5900000 - f6c78000)
[    2.512761] Simple Boot Flag at 0x36 set to 0x1
[    2.513013] microcode: CPU0 sig=0x10661, pf=0x2, revision=0x31
[    2.513124] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    2.513185] Scanning for low memory corruption every 60 seconds
[    2.513781] futex hash table entries: 512 (order: 3, 32768 bytes)
[    2.513822] Initialise system trusted keyring
[    2.513863] audit: initializing netlink subsys (disabled)
[    2.513902] audit: type=2000 audit(1452132806.508:1): initialized
[    2.514430] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    2.518969] zpool: loaded
[    2.518973] zbud: loaded
[    2.519106] VFS: Disk quotas dquot_6.5.2
[    2.519195] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    2.520336] fuse init (API version 7.23)
[    2.520683] Key type big_key registered
[    2.521078] Key type asymmetric registered
[    2.521083] Asymmetric key parser 'x509' registered
[    2.521113] bounce: pool size: 64 pages
[    2.521200] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    2.521249] io scheduler noop registered
[    2.521254] io scheduler deadline registered (default)
[    2.521336] io scheduler cfq registered
[    2.521526] pcieport 0000:00:1c.0: enabling device (0100 -> 0103)
[    2.521899] pcieport 0000:00:1c.2: enabling device (0100 -> 0103)
[    2.522241] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    2.522281] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    2.522349] vesafb: mode is 1024x768x32, linelength=4096, pages=0
[    2.522351] vesafb: scrolling: redraw
[    2.522354] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    2.522764] vesafb: framebuffer at 0xc0000000, mapped to 0xf8480000, using 3072k, total 3072k
[    2.522981] Console: switching to colour frame buffer device 128x48
[    2.523014] fb0: VESA VGA frame buffer device
[    2.523066] intel_idle: does not run on family 6 model 22
[    2.556039] ACPI: AC Adapter [ACAD] (on-line)
[    2.556225] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[    2.556249] ACPI: Lid Switch [LID]
[    2.556349] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[    2.556355] ACPI: Power Button [PWRB]
[    2.556459] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[    2.556463] ACPI: Power Button [PWRF]
[    2.556564] input: Sleep Button as /devices/LNXSYSTM:00/LNXSLPBN:00/input/input3
[    2.556568] ACPI: Sleep Button [SLPF]
[    2.556578] ACPI Error: Could not enable SleepButton event (20141107/evxfevnt-212)
[    2.556583] ACPI Warning: Could not enable fixed event - SleepButton (3) (20141107/evxface-643)
[    2.556657] button: probe of LNXSLPBN:00 failed with error -22
[    2.588087] tsc: Marking TSC unstable due to TSC halts in idle
[    2.588101] ACPI: acpi_idle registered with cpuidle
[    2.684096] thermal LNXTHERM:00: registered as thermal_zone0
[    2.684100] ACPI: Thermal Zone [TZ01] (55 C)
[    2.684282] thermal LNXTHERM:01: registered as thermal_zone1
[    2.684285] ACPI: Thermal Zone [TZ02] (27 C)
[    2.684403] GHES: HEST is not enabled!
[    2.684650] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    2.688091] isapnp: Scanning for PnP cards...
[    2.998921] isapnp: No Plug & Play device found
[    3.040176] ACPI: Battery Slot [BAT1] (battery present)
[    3.040365] Linux agpgart interface v0.103
[    3.040462] agpgart-intel 0000:00:00.0: Intel 945GM Chipset
[    3.040489] agpgart-intel 0000:00:00.0: detected gtt size: 262144K total, 262144K mappable
[    3.040645] agpgart-intel 0000:00:00.0: detected 8192K stolen memory
[    3.040811] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000
[    3.043898] brd: module loaded
[    3.045494] loop: module loaded
[    3.045828] ata_piix 0000:00:1f.1: version 2.13
[    3.047197] scsi host0: ata_piix
[    3.047362] scsi host1: ata_piix
[    3.047473] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1810 irq 14
[    3.047476] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15
[    3.047681] libphy: Fixed MDIO Bus: probed
[    3.047687] tun: Universal TUN/TAP device driver, 1.6
[    3.047688] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    3.047928] PPP generic driver version 2.4.2
[    3.048112] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.048123] ehci-pci: EHCI PCI platform driver
[    3.048357] ehci-pci 0000:00:1d.7: EHCI Host Controller
[    3.048369] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    3.048390] ehci-pci 0000:00:1d.7: debug port 1
[    3.052324] ehci-pci 0000:00:1d.7: cache line size of 64 is not supported
[    3.052360] ata2: port disabled--ignoring
[    3.052403] ehci-pci 0000:00:1d.7: irq 23, io mem 0xd0544000
[    3.064048] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    3.064140] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    3.064144] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.064147] usb usb1: Product: EHCI Host Controller
[    3.064150] usb usb1: Manufacturer: Linux 3.19.0-31-generic ehci_hcd
[    3.064153] usb usb1: SerialNumber: 0000:00:1d.7
[    3.064389] hub 1-0:1.0: USB hub found
[    3.064401] hub 1-0:1.0: 6 ports detected
[    3.064747] ehci-platform: EHCI generic platform driver
[    3.064772] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    3.064781] ohci-pci: OHCI PCI platform driver
[    3.064807] ohci-platform: OHCI generic platform driver
[    3.064831] uhci_hcd: USB Universal Host Controller Interface driver
[    3.065030] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    3.065040] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    3.065051] uhci_hcd 0000:00:1d.0: detected 2 ports
[    3.065078] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001820
[    3.065156] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    3.065160] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.065163] usb usb2: Product: UHCI Host Controller
[    3.065166] usb usb2: Manufacturer: Linux 3.19.0-31-generic uhci_hcd
[    3.065169] usb usb2: SerialNumber: 0000:00:1d.0
[    3.065393] hub 2-0:1.0: USB hub found
[    3.065404] hub 2-0:1.0: 2 ports detected
[    3.065760] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    3.065770] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    3.065779] uhci_hcd 0000:00:1d.1: detected 2 ports
[    3.065822] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001840
[    3.065899] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    3.065902] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.065906] usb usb3: Product: UHCI Host Controller
[    3.065908] usb usb3: Manufacturer: Linux 3.19.0-31-generic uhci_hcd
[    3.065911] usb usb3: SerialNumber: 0000:00:1d.1
[    3.066134] hub 3-0:1.0: USB hub found
[    3.066145] hub 3-0:1.0: 2 ports detected
[    3.066501] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    3.066511] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    3.066520] uhci_hcd 0000:00:1d.2: detected 2 ports
[    3.066561] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001860
[    3.066643] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    3.066647] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.066650] usb usb4: Product: UHCI Host Controller
[    3.066653] usb usb4: Manufacturer: Linux 3.19.0-31-generic uhci_hcd
[    3.066656] usb usb4: SerialNumber: 0000:00:1d.2
[    3.066879] hub 4-0:1.0: USB hub found
[    3.066889] hub 4-0:1.0: 2 ports detected
[    3.067187] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    3.087017] serio: i8042 KBD port at 0x60,0x64 irq 1
[    3.087025] serio: i8042 AUX port at 0x60,0x64 irq 12
[    3.087286] mousedev: PS/2 mouse device common for all mice
[    3.088612] rtc_cmos 00:05: RTC can wake from S4
[    3.088820] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[    3.088861] rtc_cmos 00:05: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[    3.088880] i2c /dev entries driver
[    3.088985] device-mapper: uevent: version 1.0.3
[    3.089128] device-mapper: ioctl: 4.29.0-ioctl (2014-10-28) initialised: dm-devel@redhat.com
[    3.089182] platform eisa.0: Probing EISA bus 0
[    3.089189] platform eisa.0: EISA: Cannot allocate resource for mainboard
[    3.089194] platform eisa.0: Cannot allocate resource for EISA slot 1
[    3.089197] platform eisa.0: Cannot allocate resource for EISA slot 2
[    3.089201] platform eisa.0: Cannot allocate resource for EISA slot 3
[    3.089204] platform eisa.0: Cannot allocate resource for EISA slot 4
[    3.089208] platform eisa.0: Cannot allocate resource for EISA slot 5
[    3.089211] platform eisa.0: Cannot allocate resource for EISA slot 6
[    3.089215] platform eisa.0: Cannot allocate resource for EISA slot 7
[    3.089219] platform eisa.0: Cannot allocate resource for EISA slot 8
[    3.089221] platform eisa.0: EISA: Detected 0 cards
[    3.089243] cpufreq-nforce2: No nForce2 chipset.
[    3.089259] ledtrig-cpu: registered to indicate activity on CPUs
[    3.089274] PCCT header not found.
[    3.089275] ACPI PCC probe failed.
[    3.089485] TCP: cubic registered
[    3.089765] NET: Registered protocol family 10
[    3.090183] NET: Registered protocol family 17
[    3.090201] Key type dns_resolver registered
[    3.090532] Using IPI No-Shortcut mode
[    3.090763] Loading compiled-in X.509 certificates
[    3.096467] Loaded X.509 cert 'Magrathea: Glacier signing key: 2b381a0b6dbe4494a532c7d9eb235639588adb70'
[    3.096494] registered taskstats version 1
[    3.100269] Key type trusted registered
[    3.106916] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[    3.109360] Key type encrypted registered
[    3.109375] AppArmor: AppArmor sha1 policy hashing enabled
[    3.109381] ima: No TPM chip found, activating TPM-bypass!
[    3.109414] evm: HMAC attrs: 0x1
[    3.109845]   Magic number: 0:869:206
[    3.109977] rtc_cmos 00:05: setting system clock to 2016-01-07 02:13:27 UTC (1452132807)
[    3.110079] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    3.110082] EDD information not available.
[    3.110231] PM: Hibernation image not present or could not be loaded.
[    3.208426] ata1.00: ATAPI: Optiarc DVD RW AD-7530A, EH31, max MWDMA2
[    3.224307] ata1.00: configured for MWDMA2
[    3.226358] scsi 0:0:0:0: CD-ROM            Optiarc  DVD RW AD-7530A  EH31 PQ: 0 ANSI: 5
[    3.246441] sr 0:0:0:0: [sr0] scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    3.246445] cdrom: Uniform CD-ROM driver Revision: 3.20
[    3.246688] sr 0:0:0:0: Attached scsi CD-ROM sr0
[    3.246798] sr 0:0:0:0: Attached scsi generic sg0 type 5
[    3.247415] Freeing unused kernel memory: 892K (c1a99000 - c1b78000)
[    3.247480] Write protecting the kernel text: 7120k
[    3.247568] Write protecting the kernel read-only data: 3016k
[    3.247570] NX-protecting the kernel data: 5168k
[    3.267681] random: systemd-udevd urandom read with 12 bits of entropy available
[    3.377351] 8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[    3.377359] 8139cp 0000:08:08.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[    3.418917] 8139too: 8139too Fast Ethernet driver 0.9.28
[    3.418988] 8139too 0000:08:08.0: enabling device (0105 -> 0107)
[    3.424987] ahci 0000:00:1f.2: version 3.0
[    3.425323] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x1 impl SATA mode
[    3.425329] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part
[    3.429795] 8139too 0000:08:08.0 eth0: RealTek RTL8139 at 0x00012000, 00:1b:38:30:2e:3c, IRQ 16
[    3.436054] scsi host2: ahci
[    3.445259] scsi host3: ahci
[    3.450442] scsi host4: ahci
[    3.457115] scsi host5: ahci
[    3.457288] ata3: SATA max UDMA/133 abar m1024@0xd0544400 port 0xd0544500 irq 26
[    3.457291] ata4: DUMMY
[    3.457294] ata5: DUMMY
[    3.457296] ata6: DUMMY
[    3.564053] usb 2-1: new full-speed USB device number 2 using uhci_hcd
[    3.730633] usb 2-1: New USB device found, idVendor=045e, idProduct=0745
[    3.730638] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    3.730641] usb 2-1: Product: Microsoft® Nano Transceiver v2.0
[    3.730645] usb 2-1: Manufacturer: Microsoft
[    3.749760] hidraw: raw HID events driver (C) Jiri Kosina
[    3.772457] usb 4-2: new low-speed USB device number 2 using uhci_hcd
[    3.776622] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    3.782078] ata3.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[    3.782085] ata3.00: ATA-7: ST94813AS, 7.24, max UDMA/100
[    3.782089] ata3.00: 78165360 sectors, multi 16: LBA48
[    3.785641] ata3.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[    3.785652] ata3.00: configured for UDMA/100
[    3.785810] scsi 2:0:0:0: Direct-Access     ATA      ST94813AS        7.24 PQ: 0 ANSI: 5
[    3.786309] sd 2:0:0:0: [sda] 78165360 512-byte logical blocks: (40.0 GB/37.2 GiB)
[    3.786388] sd 2:0:0:0: [sda] Write Protect is off
[    3.786392] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    3.786426] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.786852] sd 2:0:0:0: Attached scsi generic sg1 type 0
[    3.796243] usbcore: registered new interface driver usbhid
[    3.796247] usbhid: USB HID core driver
[    3.816206] input: Microsoft Microsoft® Nano Transceiver v2.0 as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1:1.0/0003:045E:0745.0001/input/input7
[    3.839603]  sda: sda1 sda2 < sda5 sda6 >
[    3.840297] sd 2:0:0:0: [sda] Attached SCSI disk
[    3.872333] hid-generic 0003:045E:0745.0001: input,hidraw0: USB HID v1.11 Keyboard [Microsoft Microsoft® Nano Transceiver v2.0] on usb-0000:00:1d.0-1/input0
[    3.874883] input: Microsoft Microsoft® Nano Transceiver v2.0 as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1:1.1/0003:045E:0745.0002/input/input8
[    3.928452] hid-generic 0003:045E:0745.0002: input,hidraw1: USB HID v1.11 Mouse [Microsoft Microsoft® Nano Transceiver v2.0] on usb-0000:00:1d.0-1/input1
[    3.949190] input: Microsoft Microsoft® Nano Transceiver v2.0 as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1:1.2/0003:045E:0745.0003/input/input9
[    3.950645] usb 4-2: New USB device found, idVendor=046d, idProduct=c50a
[    3.950650] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    3.950654] usb 4-2: Product: USB Receiver
[    3.950657] usb 4-2: Manufacturer: Logitech
[    3.972339] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/0003:046D:C50A.0004/input/input10
[    4.004661] hid-generic 0003:046D:C50A.0004: input,hidraw2: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1d.2-2/input0
[    4.013483] hid-generic 0003:045E:0745.0003: input,hiddev0,hidraw3: USB HID v1.11 Device [Microsoft Microsoft® Nano Transceiver v2.0] on usb-0000:00:1d.0-1/input2
[    4.323090] psmouse serio1: synaptics: Touchpad model: 1, fw: 6.2, id: 0x1a0b1, caps: 0xa04713/0x200000/0x0, board id: 0, fw id: 152129
[    4.388812] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6
[    5.079860] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
[    5.347572] random: nonblocking pool is initialized
[    5.897663] systemd[1]: RTC configured in localtime, applying delta of 60 minutes to system time.
[    6.279512] systemd[1]: Inserted module 'autofs4'
[    6.460132] systemd[1]: systemd 219 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN)
[    6.460342] systemd[1]: Detected architecture x86.
[    6.471847] systemd[1]: Set hostname to <jan-HP-G5000-GH964EA-UUW>.
[    8.090784] systemd[1]: Reached target Encrypted Volumes.
[    8.090808] systemd[1]: Starting Encrypted Volumes.
[    8.090878] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    8.090895] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[    8.091218] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    8.091240] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[    8.091313] systemd[1]: Created slice Root Slice.
[    8.091330] systemd[1]: Starting Root Slice.
[    8.091394] systemd[1]: Listening on Delayed Shutdown Socket.
[    8.091411] systemd[1]: Starting Delayed Shutdown Socket.
[    8.091461] systemd[1]: Listening on udev Kernel Socket.
[    8.091477] systemd[1]: Starting udev Kernel Socket.
[    8.091537] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[    8.091553] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[    8.091713] systemd[1]: Created slice User and Session Slice.
[    8.091731] systemd[1]: Starting User and Session Slice.
[    8.091872] systemd[1]: Listening on Journal Audit Socket.
[    8.091889] systemd[1]: Starting Journal Audit Socket.
[    8.091941] systemd[1]: Listening on fsck to fsckd communication Socket.
[    8.091958] systemd[1]: Starting fsck to fsckd communication Socket.
[    8.092076] systemd[1]: Listening on Journal Socket (/dev/log).
[    8.092093] systemd[1]: Starting Journal Socket (/dev/log).
[    8.092274] systemd[1]: Created slice System Slice.
[    8.092303] systemd[1]: Starting System Slice.
[    8.093324] systemd[1]: Starting Increase datagram queue length...
[    8.093371] systemd[1]: Reached target Slices.
[    8.093397] systemd[1]: Starting Slices.
[    8.123988] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[    8.124044] systemd[1]: Starting Device-mapper event daemon FIFOs.
[    8.124292] systemd[1]: Created slice system-getty.slice.
[    8.124311] systemd[1]: Starting system-getty.slice.
[    8.124390] systemd[1]: Listening on udev Control Socket.
[    8.124407] systemd[1]: Starting udev Control Socket.
[    8.124496] systemd[1]: Listening on Journal Socket.
[    8.124523] systemd[1]: Starting Journal Socket.
[    8.125462] systemd[1]: Starting Nameserver information manager...
[    8.126467] systemd[1]: Mounting POSIX Message Queue File System...
[    8.191855] systemd[1]: Started Set Up Additional Binary Formats.
[    8.193069] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[    8.194127] systemd[1]: Starting udev Coldplug all Devices...
[    8.195178] systemd[1]: Starting Uncomplicated firewall...
[    8.196327] systemd[1]: Started Read required files in advance.
[    8.201094] systemd[1]: Starting Read required files in advance...
[    8.202633] systemd[1]: Mounting Debug File System...
[    8.203763] systemd[1]: Starting Setup Virtual Console...
[    8.205026] systemd[1]: Mounting Huge Pages File System...
[    8.381349] systemd[1]: Starting Load Kernel Modules...
[    8.381411] systemd[1]: Reached target Remote File Systems (Pre).
[    8.381437] systemd[1]: Starting Remote File Systems (Pre).
[    8.469902] systemd[1]: Started Setup Virtual Console.
[    8.647718] systemd[1]: Started Create list of required static device nodes for the current kernel.
[    8.649057] systemd[1]: Starting Create Static Device Nodes in /dev...
[    8.678650] systemd[1]: Started Uncomplicated firewall.
[    8.708914] systemd[1]: Mounted Huge Pages File System.
[    8.708991] systemd[1]: Mounted Debug File System.
[    8.709031] systemd[1]: Mounted POSIX Message Queue File System.
[    8.709441] systemd[1]: Started Increase datagram queue length.
[    8.713819] systemd[1]: Listening on Syslog Socket.
[    8.713866] systemd[1]: Starting Syslog Socket.
[    8.714987] systemd[1]: Starting Journal Service...
[    8.873543] systemd[1]: Started Nameserver information manager.
[    8.902865] systemd[1]: Started udev Coldplug all Devices.
[    8.932287] systemd[1]: Starting udev Wait for Complete Device Initialization...
[    9.455751] lp: driver loaded but no devices found
[    9.518132] ppdev: user-space parallel port driver
[    9.638324] systemd[1]: Started Journal Service.
[   11.479234] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[   11.560905] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   11.691683] [drm] Initialized drm 1.1.0 20060810
[   11.756404] acpi device:04: registered as cooling_device1
[   11.756554] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:01/input/input11
[   11.809662] wmi: Mapper loaded
[   12.141891] intel_rng: FWH not detected
[   12.248418] [drm] Memory usable by graphics device = 256M
[   12.248426] checking generic (c0000000 300000) vs hw (c0000000 10000000)
[   12.248429] fb: switching to inteldrmfb from VESA VGA
[   12.248464] Console: switching to colour dummy device 80x25
[   12.248566] [drm] Replacing VGA console driver
[   12.250902] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[   12.250907] [drm] Driver supports precise vblank timestamp query.
[   12.251045] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[   12.373404] cfg80211: Calling CRDA to update world regulatory domain
[   12.649617] [drm] initialized overlay support
[   12.649754] [drm] Initialized i915 1.6.0 20141121 for 0000:00:02.0 on minor 0
[   12.649895] ACPI Warning: SystemIO range 0x00001028-0x0000102f conflicts with OpRegion 0x00001000-0x0000107f (\PMIO) (20141107/utaddress-258)
[   12.649904] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   12.649909] ACPI Warning: SystemIO range 0x000011b0-0x000011bf conflicts with OpRegion 0x00001180-0x000011bb (\GPIO) (20141107/utaddress-258)
[   12.649914] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   12.649917] ACPI Warning: SystemIO range 0x00001180-0x000011af conflicts with OpRegion 0x00001180-0x000011bb (\GPIO) (20141107/utaddress-258)
[   12.649922] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   12.649924] lpc_ich: Resource conflict(s) found affecting gpio_ich
[   12.789113] leds_ss4200: no LED devices found
[   12.808302] fbcon: inteldrmfb (fb0) is primary device
[   12.808368] Console: switching to colour frame buffer device 160x50
[   12.808417] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[   12.808420] i915 0000:00:02.0: registered panic notifier
[   12.854035] sound hdaudioC0D0: CX20549 (Venice): BIOS auto-probing.
[   12.854308] sound hdaudioC0D0: autoconfig: line_outs=1 (0x10/0x0/0x0/0x0/0x0) type:speaker
[   12.854313] sound hdaudioC0D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   12.854316] sound hdaudioC0D0:    hp_outs=1 (0x11/0x0/0x0/0x0/0x0)
[   12.854319] sound hdaudioC0D0:    mono: mono_out=0x0
[   12.854323] sound hdaudioC0D0:    dig-out=0x13/0x0
[   12.854326] sound hdaudioC0D0:    inputs:
[   12.854329] sound hdaudioC0D0:      Mic=0x14
[   12.855718] sound hdaudioC0D0: Enable sync_write for stable communication
[   12.863369] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[   12.863528] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
[   13.209318] input: HP WMI hotkeys as /devices/virtual/input/input14
[   14.463899] wl: module license 'MIXED/Proprietary' taints kernel.
[   14.463906] Disabling lock debugging due to kernel taint
[   14.477714] wl: module verification failed: signature and/or  required key missing - tainting kernel
[   14.537251] malloc in abgphy done
[   14.537698] wl driver 6.30.223.248 (r487574) failed with code 21
[   14.537731] ------------[ cut here ]------------
[   14.537791] kernel BUG at include/net/cfg80211.h:3493!
[   14.537845] invalid opcode: 0000 [#1] SMP
[   14.537901] Modules linked in: wl(POE+) hp_wmi sparse_keymap snd_hda_codec_conexant snd_hda_codec_generic snd_hda_intel coretemp snd_hda_controller snd_hda_codec joydev cfg80211 snd_hwdep lpc_ich serio_raw i915 snd_pcm snd_seq_midi snd_seq_midi_event snd_rawmidi snd_seq wmi snd_seq_device snd_timer drm_kms_helper snd drm soundcore i2c_algo_bit shpchp video mac_hid parport_pc ppdev lp parport autofs4 hid_generic usbhid hid ahci 8139too psmouse libahci 8139cp pata_acpi mii
[   14.538550] CPU: 0 PID: 242 Comm: systemd-udevd Tainted: P           OE  3.19.0-31-generic #36-Ubuntu
[   14.538640] Hardware name: Hewlett-Packard HP G5000 (GH964EA#UUW)            /30C6, BIOS F.24 04/25/2007
[   14.538735] task: f69cc360 ti: f4624000 task.ti: f4624000
[   14.538791] EIP: 0060:[<f9954e08>] EFLAGS: 00010246 CPU: 0
[   14.538899] EIP is at wl_cfg80211_detach+0x108/0x120 [wl]
[   14.538955] EAX: 00000000 EBX: f6abfa34 ECX: f6abec00 EDX: f6abfa34
[   14.539018] ESI: f4e09000 EDI: f6abec00 EBP: f4625bc0 ESP: f4625bb0
[   14.539081]  DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[   14.539136] CR0: 80050033 CR2: b74351f0 CR3: 34609000 CR4: 000007f0
[   14.539199] Stack:
[   14.539223]  00000086 f6abfa34 f4e09000 f6abec00 f4625bd8 f994c9f3 f6abfa0c f6abfa00
[   14.539340]  f4e09000 f6abec00 f4625c80 f994d1f2 00000400 c10ae04d 00000000 00000282
[   14.539456]  00000327 00000000 00000002 00000000 00000328 00440001 00000002 00000000
[   14.539572] Call Trace:
[   14.539650]  [<f994c9f3>] wl_free_if.isra.15+0x23/0xa0 [wl]
[   14.539753]  [<f994d1f2>] wl_free+0x52/0x270 [wl]
[   14.539808]  [<c10ae04d>] ? log_store+0x1cd/0x210
[   14.539859]  [<c10b0896>] ? vprintk_emit+0x326/0x5b0
[   14.539913]  [<c10b0ca1>] ? vprintk_default+0x41/0x60
[   14.540005]  [<f994d76c>] wl_pci_probe+0x35c/0x6e0 [wl]
[   14.540005]  [<c147bd41>] ? __pm_runtime_resume+0x51/0x70
[   14.540005]  [<c138832f>] pci_device_probe+0x6f/0xd0
[   14.540005]  [<c1214765>] ? sysfs_create_link+0x25/0x50
[   14.540005]  [<c1472103>] driver_probe_device+0xa3/0x3e0
[   14.540005]  [<c1388262>] ? pci_match_device+0xd2/0x100
[   14.540005]  [<c14724f9>] __driver_attach+0x79/0x80
[   14.540005]  [<c1472480>] ? __device_attach+0x40/0x40
[   14.540005]  [<c147040f>] bus_for_each_dev+0x4f/0x80
[   14.540005]  [<c1471bce>] driver_attach+0x1e/0x20
[   14.540005]  [<c1472480>] ? __device_attach+0x40/0x40
[   14.540005]  [<c1471837>] bus_add_driver+0x167/0x240
[   14.540005]  [<f86ba000>] ? 0xf86ba000
[   14.540005]  [<f86ba000>] ? 0xf86ba000
[   14.540005]  [<c1472c0d>] driver_register+0x5d/0xf0
[   14.540005]  [<c1386ce3>] __pci_register_driver+0x33/0x40
[   14.540005]  [<f86ba06d>] wl_module_init+0x6d/0x1000 [wl]
[   14.540005]  [<c1002136>] do_one_initcall+0xc6/0x200
[   14.540005]  [<f86ba000>] ? 0xf86ba000
[   14.540005]  [<c119540d>] ? kfree+0x12d/0x140
[   14.540005]  [<c11820d5>] ? __vunmap+0xa5/0xf0
[   14.540005]  [<c16ee230>] ? _cond_resched+0x30/0x50
[   14.540005]  [<c1196645>] ? kmem_cache_alloc_trace+0x165/0x1d0
[   14.540005]  [<c11820d5>] ? __vunmap+0xa5/0xf0
[   14.540005]  [<c10daf18>] ? load_module+0x1138/0x1a00
[   14.540005]  [<c10daf18>] ? load_module+0x1138/0x1a00
[   14.540005]  [<c10daf4b>] load_module+0x116b/0x1a00
[   14.540005]  [<c10db95d>] SyS_finit_module+0x7d/0xc0
[   14.540005]  [<c116376b>] ? vm_mmap_pgoff+0x7b/0xa0
[   14.540005]  [<c16f1e1f>] sysenter_do_call+0x12/0x12
[   14.540005] Code: 00 00 00 b8 02 00 00 00 3e 0f c0 83 84 04 00 00 a8 01 74 c2 83 e0 fe 8d 50 02 8b 45 f0 0f b6 d2 66 66 90 66 66 90 eb ae 8d 76 00 <0f> 0b 8d b6 00 00 00 00 0f 0b 8d b4 26 00 00 00 00 8d bc 27 00
[   14.540005] EIP: [<f9954e08>] wl_cfg80211_detach+0x108/0x120 [wl] SS:ESP 0068:f4625bb0
[   14.562423] ---[ end trace 8b501721de343b9a ]---
[   15.057683] cfg80211: World regulatory domain updated:
[   15.057693] cfg80211:  DFS Master region: unset
[   15.057695] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   15.057699] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   15.057703] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   15.057706] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   15.057709] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   15.057713] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   15.057716] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   15.057719] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   15.057723] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   16.261037] Adding 2085884k swap on /dev/sda6.  Priority:-1 extents:1 across:2085884k FS
[   16.779741] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro
[   17.118219] systemd-journald[197]: Received request to flush runtime journal from PID 1
[   19.932296] audit: type=1400 audit(1452129224.319:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/lightdm/lightdm-guest-session" pid=393 comm="apparmor_parser"
[   19.933294] audit: type=1400 audit(1452129224.319:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="chromium" pid=393 comm="apparmor_parser"
[   19.989332] audit: type=1400 audit(1452129224.375:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=393 comm="apparmor_parser"
[   19.989348] audit: type=1400 audit(1452129224.375:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=393 comm="apparmor_parser"
[   19.989358] audit: type=1400 audit(1452129224.375:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=393 comm="apparmor_parser"
[   19.989367] audit: type=1400 audit(1452129224.375:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=393 comm="apparmor_parser"
[   20.046744] audit: type=1400 audit(1452129224.431:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/evince" pid=393 comm="apparmor_parser"
[   20.046763] audit: type=1400 audit(1452129224.431:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="sanitized_helper" pid=393 comm="apparmor_parser"
[   20.046773] audit: type=1400 audit(1452129224.431:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/evince-previewer" pid=393 comm="apparmor_parser"
[   20.046782] audit: type=1400 audit(1452129224.431:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="sanitized_helper" pid=393 comm="apparmor_parser"
[   28.289158] 8139too 0000:08:08.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1

[lath]

[ 0.000000] RAMDISK: [mem 0x35900000-0x36c77fff]
...
[ 0.000000] ACPI: BIOS bug: multiple APIC/MADT found, using 0
[ 0.000000] ACPI: If "acpi_apic_instance=2" works better, notify linux-acpi@vger.kernel.org
...
[ 0.096535] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
...
[ 0.312587] pnp: PnP ACPI: found 6 devices
[ 0.312597] PnPBIOS: Disabled by ACPI PNP
...
[ 2.556039] ACPI: AC Adapter [ACAD] (on-line)
[ 2.556225] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[ 2.556249] ACPI: Lid Switch [LID]
[ 2.556349] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 2.556355] ACPI: Power Button [PWRB]
[ 2.556459] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 2.556463] ACPI: Power Button [PWRF]
[ 2.556564] input: Sleep Button as /devices/LNXSYSTM:00/LNXSLPBN:00/input/input3
[ 2.556568] ACPI: Sleep Button [SLPF]
[ 2.556578] ACPI Error: Could not enable SleepButton event (20141107/evxfevnt-212)
[ 2.556583] ACPI Warning: Could not enable fixed event - SleepButton (3) (20141107/evxface-643)
[ 2.556657] button: probe of LNXSLPBN:00 failed with error -22

Note: Kernen overgiver kontrollen af styresystemet til init processen, her systemd

Note: Her starter init processen (process id 1) PID 1

[ 5.897663] systemd[1]: RTC configured in localtime, applying delta of 60 minutes to system time.
...
[ 11.479234] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
...
[ 11.756404] acpi device:04: registered as cooling_device1
...
[ 12.649895] ACPI Warning: SystemIO range 0x00001028-0x0000102f conflicts with OpRegion 0x00001000-0x0000107f (\PMIO) (20141107/utaddress-258)
[ 12.649904] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 12.649909] WarningACPI : SystemIO range 0x000011b0-0x000011bf conflicts with OpRegion 0x00001180-0x000011bb (\GPIO) (20141107/utaddress-258)
[ 12.649914] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 12.649917] ACPI Warning: SystemIO range 0x00001180-0x000011af conflicts with OpRegion 0x00001180-0x000011bb (\GPIO) (20141107/utaddress-258)
[ 12.649922] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
...
[ 14.537791] kernel BUG at include/net/cfg80211.h:3493!
...

Jeg har klippet i output. En elipsis (...) betyder at jeg har klippet fra 1 til flere linier ud.
Den 3. linie er noget du måske bør prøve. Det i anførselstegnene skal tilføjes til kerne linien som kernen kigger på lige efter at den er startet op.

Ud fra output synes jeg at det ser ud til at en opgradering af BIOS/firmware version er en rigtig god ide (,hvis der ellers er en nyere version).

Det ser også ud til at der er en kerne bug vedrørende noget WiFi netværks relateret.

/Lars

[AJenbo]

Jeg er enig med lath om at du bør prøve at se om BIOS kan opdateres.

Hvis ikke, eller hvis det ikke hjælper så prøv om det hjælper at tilføje acpi_apic_instance=2, du kan bruge følgende guide til at hjælpe med hvordan du indsætter det:
https://ubuntudanmark.dk/blog/artikler/ ... nomodeset/
(spring de 2 første billeder over, og din kommando er så acpi_apic_instance=2 frem for nomodeset)

Bemærk at 15.04 udløber her januar 2016 så den bør opgraderes ASAP.

@lath "PnPBIOS: Disabled by ACPI PNP" er ikke et problem, men blot en bemærkning om at den benytter ACPI (hvilket er bedre) frem for PnPBIOS.

[MrDong]

Hej Lath
Jeg vil først sige tak for at du vil hjælp mig, dernæst forstår jeg godt hvad du skriver, men jeg forstår ikke hvad og hvordan du mener jeg skal sætte ell rette de linjer du forslår ?
Du har også ret i at mit trådløs wifi på pc ikke virker, har en knap men den regere ikke når man trykker på den.
Synes det er et stort arbejde med at klippe ud de linjer du mener er problemet, men altså jeg forstår ikke rigtigt hvad det er jeg skal gøre, Sorry

Hej AJenbo
Jeg forsøgte at sætte det ind du skrev jeg skulle, prøvede at følge det link du sendte med, jeg satte nu altså det ind i starten af første linje trykkede herefter ctrl-x derefter den startede den op og jeg prøvede lukke den ned igen og den stoppede samme sted som altid. Jeg startede op igen kiggede efter om det jeg havde skrevet skulle slettes igen, men der stod intet hmm. Måske jeg gjorde det forkert. Hvor skal det stå det som du skrev jeg skulle skrive? Er det ligemeget hvor det står?

image.jpg (195.4 KiB) Vist 568 gange

[AJenbo]

Jeg tænkte nok du ville have lidt svært ved at følge Laths instruktioner, hvilket er hvorfor jeg forsøgte at beskrive det lidt nærmere, så du er allerede i gang med det

Du skal indsætte teksten mellem quiet og splash, jeg har markeret det med en grøn pil:

image.jpg (200.1 KiB) Vist 561 gange

Guiden skulle gerne beskrive at det kun er midlertidigt når du skriver det ind her, det er for at teste om det virker, hvis det virker er der senere i guiden beskrevet hvor dan du skal gøre for at gøre det permanent, men det er kun relevant hvis det hjælper.

[AJenbo]

Seneste bios opdatering til dit system kan hentes her:
http://ftp.hp.com/pub/softpaq/sp37501-38000/sp37633.exe

[MrDong]

Hej igen igen Ajenbo
Jeg har lavet en perfekt bios opdate var nemt nok, jeg har også fulgt dit råd og prøvede at sætte den linje ind som du beskriver, men det har ingen virkning den stopper som den har gjort hele tiden, må holde tænd knappen nede før den slukker helt desværre.

Jeg har også forsøgt at opdatere til ny version af ubuntu men den står helt stille her hvad er nu det ?
jan@jan-HP-G5000-GH964EA-UUW:~$ sudo dpkg --configure -a
Sætter bcmwl-kernel-source (6.30.223.248+bdcom-0ubuntu7) op ...
Removing old bcmwl-6.30.223.248+bdcom DKMS files...

-------- Uninstall Beginning --------
Module: bcmwl
Version: 6.30.223.248+bdcom
Kernel: 4.2.0-23-generic (i686)
-------------------------------------

Status: Before uninstall, this module version was ACTIVE on this kernel.

wl.ko:
- Uninstallation
- Deleting from: /lib/modules/4.2.0-23-generic/updates/dkms/
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.

depmod............

DKMS: uninstall completed.

Hjælp

[AJenbo]

Prøv i stedet at tilføje dette:

Kode: Vælg alt

acpi=off

Jeg kan ikke se noget problem i det output du har indsat. Men det ser ud til at der har været et problem tidligere ud fra den kommando du køre.

[lath]

Hej igen igen Ajenbo
Jeg har lavet en perfekt bios opdate var nemt nok, jeg har også fulgt dit råd og prøvede at sætte den linje ind som du beskriver, men det har ingen virkning den stopper som den har gjort hele tiden, må holde tænd knappen nede før den slukker helt desværre.

Jeg har også forsøgt at opdatere til ny version af ubuntu men den står helt stille her hvad er nu det ?
jan@jan-HP-G5000-GH964EA-UUW:~$ sudo dpkg --configure -a
Sætter bcmwl-kernel-source (6.30.223.248+bdcom-0ubuntu7) op ...
Removing old bcmwl-6.30.223.248+bdcom DKMS files...

-------- Uninstall Beginning --------
Module: bcmwl
Version: 6.30.223.248+bdcom
Kernel: 4.2.0-23-generic (i686)
-------------------------------------

Status: Before uninstall, this module version was ACTIVE on this kernel.
DKMS advarer dig også om at kerne modulet var aktivt - det vil sige indlæst i kernen.

wl.ko:
- Uninstallation
- Deleting from: /lib/modules/4.2.0-23-generic/updates/dkms/
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.

depmod............

DKMS: uninstall completed.

Hjælp

Det betyder at det lykkedes DKMS at afinstallere en kernel-space device driver, som er et kerne modul, der hedder bcmwl.
Hint:

DKMS: uninstall completed

bcmwl kunne umiddelbart lyde som en device driver for noget Broadcom wireless (WLAN/WiFi) hardware i din computer.

En lille fremmedordbog for alle de svære ord:

• Device driver: En device driver er det der sørger for at en styresystem kerne - her Linux (=kernen i en Linux distribution såsom Ubuntu) - kan "snakke" med hardware/noget man kan slå sig på..
• kernel-space: Kernel-space er det område af fysisk RAM hvor kernen og dens device drivere bor.
• Programmer holder til i det man kalder user-space.
  Device driver findes også i user-space, f.eks. så sker det meste USB håndtering i user-space.
• C kildekode er skrevet i et mikro sprog, der hedder C programmeringssproget. Modsætningen til et mikro sprog er et naturligt sprog. Et naturligt sprog kunne for eksempel være Dansk.
• Et kerne modul bor i fil som har fil-endelsen ".ko".
  Et kerne modul indeholder en kernel-space device driver, der kan indlæses imens kernen afvikler et Linux styresystem og dets Linux programmer, f.eks. Ubuntu.
  Genstart er aldrig nødvendigt, når man indlæser/aktiverer og deaktiverer kerne moduler.
• DKMS er noget software der bruges i user-space til at oversætte kildekode til Linux kernel-space device drivere fra Open Source kildekode.
  DKMS producerer eller deaktiverer+afinstallere et kerne modul.
  DKMS har en afhængighed til en C kildekode oversætter (en C compiler) der hedder GCC. GCC laver C kildekode (tekst) om til maskinkode, som din computers mikroprocessor kan forstå.

/Lars

[MrDong]

Hej AJenbo
Jeg har lige prøvede gøre som du skriver, og når jeg lukker ned kommer den stadigvæk til samme slut linje, derefter kan jeg så trykke en gang på sluk knap og den lukker bare ned, føles ikke som den er helt rigtigt, hvis jeg bare trykker på sluk knap når den er opstartet laver den så et totalt sluk uden at komme med nogle linjer.

Hej Lath
Tak for input og lære, du har helt ret i at der ligger et Broadcom Trådløs som ikke virker i nu, og den ber nu om at jeg skal køre denne kommando sudo --dpkg--configure-a når den så afstallere den driver og installere en ny driver ender den med at skrive DKMS: uninstall completed

Derefter står den stille i den terminal kommer ikke tilbage med mit jan&jan-HP osv jeg skal selv lukke terminalen, hvis jeg så åbner ny terminal prøver at lave opdate går den bare istå sker ikke noget, må lukke PC ned ny opstart igen. Hvordan kommer man så videre nu ? hænger de 2 problemer sammen ? derfor at også det trådløse ikke virker sammen med det nedlukningsproblem ?

Takker lige igen for den hjælp man får her

[AJenbo]

Ja, den vil sikkert også blot lukke med det samme så.

Det er ikke utænkeligt at hardware hvor driveren ikke fungere kan forhændre strømstyringen i at fungere korrekt, det kan være særlig sandt for grafikkort og trådløse netværksenheder.

[MrDong]

Hej Ajenbo
Jeg fik det til at virke med at den kunne lukke rigtigt ned, det fik jeg den til da jeg fik afinstalleret Broadcom driver og installeret nogle andre Broadcom driver så virkede den rigtige nedlukning.

Men det trådløse net virker stadigvæk ikke på PCen så det er altså disse driver der forstyrre og laver problemer både på nedlukning og det trådløse net på pc.

Jeg fik det til at virke på et tidspunkt altså nedlukning, nu er det så at få de rigtige driver til at fungere på det trådløse og jeg vil tro at PC vil komme til at virke rigtigt. Har kigget på disse sider her prøvet de forskellige driver

http://askubuntu.com/questions/55868/in ... ss-drivers

Der må da være andre med samme problem og med en HP ?

Nogle der ved noget ? og takker selvfølgelig for den hjælp som jeg allerede har fået her har også været hjælpsomt

[MrDong]

Prøvede at installere nye Broadcom driver via synaptic det ville den så ikke og fik en fejlmeddelelse her
https://bugs.launchpad.net/ubuntu/+sour ... ug/1504975

Nogle der kan hjælpe med at tyde denne ?
Og hvad er det Chris mener med at han har løst sit problem med det han her skriver ? Kan jeg muligvis bruge dette og hvad er det han gør ?

I manged to fix it pretty easily just by adding a ie_len parameter

cfg80211_disconnected(ndev, 0, NULL, 0,0, GFP_KERNEL);

I just set it to 0, which may be pretty silly, but at least my driver works